Here's a snippet from running firestrike extreme, ran it this morning whilst it's still a bit cooler during this heat wave.
New ITX Build - Lian Li O5 SX
- Thread starter dancook
- Start date
Here's a snippet from running firestrike extreme, ran it this morning whilst it's still a bit cooler during this heat wave.
ordered some RAM for it now (running 8gb stick from 3 month 'old' pc)
G.SKILL TridentZ Series F4-2800C14D-32GTZ 32GB DDR4 2800 MHz C 14 1.35 V Memory Kit - Dual Colour
DDR4-2800MHz (PC4-22400), 32GB (16GBx2), CL14-14-14-35, 1.35 Volt, Dual Channel Kit
Not that you can see it side on .. it looks sweet
G.SKILL TridentZ Series F4-2800C14D-32GTZ 32GB DDR4 2800 MHz C 14 1.35 V Memory Kit - Dual Colour
DDR4-2800MHz (PC4-22400), 32GB (16GBx2), CL14-14-14-35, 1.35 Volt, Dual Channel Kit
Not that you can see it side on .. it looks sweet
I7 512gb, great screen, highly portable. Love itprocess photos when I go abroad
too pricey for me, but my uncle would probably purchase.
had trouble fitting a
G.SKILL TridentZ Series F4-2800C14D-32GTZ 32GB DDR4 2800 MHz C 14 1.35 V Memory Kit
The cpu cooler block hoses were right up against the RAM and the GSkill is wider than most and wouldn't fit at all.
Was about to send RAM back, but realised I could rotate radiator and mount cooler upside down.. it works
G.SKILL TridentZ Series F4-2800C14D-32GTZ 32GB DDR4 2800 MHz C 14 1.35 V Memory Kit
The cpu cooler block hoses were right up against the RAM and the GSkill is wider than most and wouldn't fit at all.
Was about to send RAM back, but realised I could rotate radiator and mount cooler upside down.. it works
Associate
Gorgeous PC, the cost made my eyes bleed xD
I'm just jealous, i was looking at that case but then saw the price tag and went for a more console looking thing
I'm just jealous, i was looking at that case but then saw the price tag and went for a more console looking thing
Nice work, have they changed the PCIe ribbon? And nice your rear cable work looks solo much nicer then mine lol.
It is a lovely case though, Loved building in mine. Managed to squeeze a custom loop in just with the nano, thank goodness for small cards! Do recommend you go for it, not easy in such a small case but does look epic once done with a loop IMO.
It is a lovely case though, Loved building in mine. Managed to squeeze a custom loop in just with the nano, thank goodness for small cards! Do recommend you go for it, not easy in such a small case but does look epic once done with a loop IMO.
I think they did change the PCIe Ribbon from what I've read since getting the case.
My rear cable work now has more going on, and i wouldn't say it's tidy
but it's hidden...I do want a custom loop, was going to sit on it for a bit before doing it.. soaking up any suggestions..
I saw this, but he's left the glass and front panel of the case off
https://linustechtips.com/main/topic/403348-experiment-001-never-settle/
I've seen a reservoir above the PSU and now by the GPU so that's encouraging.
Heh, my rear panel bends out slightly
This is the sort of route my loop ended up going if it helps provide any ideas. A lot harder with the smallest member of the family getting a full length GPU in along with a pump. On the larger versions there is room at the end to swap around the pump and PSU position like other builds but with the smallest member, not so easy unless you get something like the swiftech cooler.
Can probebrly see that awkward fitting from GPU to Mobo block as the riser gets in the way awkwardly. Found it slightly awkward like yourself with the VRM daughter board on the Impact board, but had to pick it as one of the few ITX boards with a full cover water block, pretty awesome on mini ITX as the whole board is effectively under a single block.
This is the sort of route my loop ended up going if it helps provide any ideas. A lot harder with the smallest member of the family getting a full length GPU in along with a pump. On the larger versions there is room at the end to swap around the pump and PSU position like other builds but with the smallest member, not so easy unless you get something like the swiftech cooler.
Can probebrly see that awkward fitting from GPU to Mobo block as the riser gets in the way awkwardly. Found it slightly awkward like yourself with the VRM daughter board on the Impact board, but had to pick it as one of the few ITX boards with a full cover water block, pretty awesome on mini ITX as the whole board is effectively under a single block.
Glad to see you got it to work for you.
My intermediate solution is to fix these two 80mm fans to the front to blow air across the gpu.
and the RGB leds are to distract from the upside down cooler master logo.
Also decided to get a slim line blu-ray writer, just in case...
My intermediate solution is to fix these two 80mm fans to the front to blow air across the gpu.
and the RGB leds are to distract from the upside down cooler master logo.
Also decided to get a slim line blu-ray writer, just in case...
Got a project log going on, but i'll update here too
Added RGB lighting and a bluray drive, but here's the lighting.
RGB Led Lighting by dancook1982, on Flickr
Added RGB lighting and a bluray drive, but here's the lighting.
RGB Led Lighting by dancook1982, on FlickrUpdated my project log, with watercooling
https://forums.overclockers.co.uk/showthread.php?t=18742072
Watercooled i6700k @ 4.8ghz+ Titan X (Pascal) overclocked by dancook1982, on Flickr
https://forums.overclockers.co.uk/showthread.php?t=18742072
Watercooled i6700k @ 4.8ghz+ Titan X (Pascal) overclocked by dancook1982, on Flickr