Search results

  1. natsu

    Watercooled Case Gallery

    Mayhems dye and DI
  2. natsu

    The Silence

    Thx guys. I have to admit that I like it a lot. Even with lightbox turned on fluid looks good. I will add 1 or 2 more pics with lightbox on when I get my DSLR back
  3. natsu

    The Silence

    It's up and running. TJ07 v3 iATX :) Thx for stopping by and supporting me :) Hope You are gonna like this one :)
  4. natsu

    Watercooled Case Gallery

    My updated TJ07 v3 iATX
  5. natsu

    The Silence

    Well... I lost 1 fitting somewhere. Don't know when or where but I'm raging right now. Did gpu->rad connection and res->rad... and that's it up until I get some flexible tubing to finish bottom chamber Edit: Problem solved with male to male short extender
  6. natsu

    The Silence

    Some progress being made. I need to make that res tube a bit shorter
  7. natsu

    The Silence

    I'm alive no worries ;) Changed my mind (again) and I stick to IATX. Alu cover are out due to very long waitiing time for some parts so I stick to MMod plexi covers. In the drive bays area... just see yourself :D
  8. natsu

    The Silence

    I like new colour :)
  9. natsu

    The Silence

    MurderBox is too expensive. Same for Martma's mods for TJ07. As for the res You can contact a person who made it for me. Hi FB page https://www.facebook.com/pages/Skeeper/786288178115655?fref=ts What do You think guys about covering I/O ports? Not sure if I like the look of it
  10. natsu

    The Silence

    Ok. It's time to go back do ATX. I have some covers already, new cover for front is coming in. I already ordered DI water, orange dye, anti corrosion and biocide and ek holder so my res could be finally still :) Lightbox is going out, both 360 and 480 going to the bottom of the case, psu to...
  11. natsu

    Project 63hPa

    Have fun with bending that rad-cpu connection :D
  12. natsu

    White knight build update time

    Am I the only not pleased with lightbox? :D Looks great on pictures but not even close to be so bright when You look at it. The MBTray though is very nice
  13. natsu

    Watercooled Case Gallery

    New case, old hardware
  14. natsu

    The Silence

    iATX beta is done. Now I know what can and what can't be done in this chasis. Few weeks from now I will swap the MB tray for the CZ tray, do some custom covers, re route the tubing and possibly change gpu
  15. natsu

    The Silence

    It doesn't look like I'm gonna finish this build anytime soon... Lack of time kills it. I even left my red gpu ext. since I no longer have free time to work with PC. I still hope this will be finished but unfortunatelly as soon as it was intended. Because of that I decided to to "final" photos...
  16. natsu

    HeretEK-An EK Vulture build

    What happened to that case? Was the MB Tray used a dinner table or what? Scracthes all over it
  17. natsu

    Which Acrylic tubing size to use?

    I have 14mm in TJ07 and thez are not too big. I would saz 14mm is just big enough for mz taste and I would go for 13mm I were You and had Evolve to work with
  18. natsu

    The Silence

    I like what I received today :) Don't know about using new backplate. Drilling the case with hardware inside is not the best thing to do but front and psu plate are going to be used :)
  19. natsu

    The Silence

    The bearings are fine, everything You can hear is moving air. I have set them to 900rpm and this makes them very silent to me and look very nice. Noctua industrial's is a bit louder at the same speed. Still about 2 weeks left for final pics. Have to wait for alu covers to be sent to me and then...
  20. natsu

    The Silence

    A bit more before final pictures :)
Back
Top Bottom