Search results

On the radiator, system is all done now :).

Do you think this is better?

Oh people also asked me to post the purpose, primarily it is a workstation for myself as a software development consultant. However it will be used for a bit of gaming here and there . Currently playing a bit of red dead 2, I can get around 105 FPS in 4K ultra settings, a bit annoying I can’t...

So, I took some advice from people on here, and they said when it was all done could I post a picture. But I decided to go one further and post a video. Where do you think i should out my 4 RGB strips? the 2080ti water block does light up too, but it was on the off part of the cycle in the...

It’s a ryzen 3950x Overclocked to 4.4 on all cores and an RTX 2080Ti (msi lightning). It will maintain this Overclock in prime 95 for 35 mins before the heat saturates too much, and is totally stable for any normal usage. I have 2x EK PE 360 with push fans, and 1x EK XL with push/pull. I...

you are missing the point of my build, my rad with push pull is 60mm thick, it’s the ek xl, without push pull only one half of the radiator gets any air flow. Fact.

I’ve found that I would need a node ighting pro module, which not only takes up another motherboard usb header, but would cost 50 quid to get this one fan lit

I’m already running 2 RGB hubs, so I guess that means I’m screwed?

You’ll have to forgive me, but I can only find standard RGB splitters, not the proprietary Corsair ones?

Hi, I have a wierd dilemma in that I have a corsair commander, and 2 RGB hubs connected to it, and 13x Corsair HD120 fans. However, as I have 13 fans, and only 12 slots in the RGB Hub, 1 cannot be connected. Is there such a thing as an RGB splitter so I can connect the last one? I have loads of...

May be a silly question, but is this a specific game? I have the ultimate rig and still can’t get above 60 frames in red dead 2 at 4K because of issues with their game...

https://i.ibb.co/X7MMhQ5/F3-C74-F67-67-BE-4032-94-E0-C40-B98404-E4-C.jpg

Ok so rig all finished and working, apart from the RGB the water block, not sure if it’s the block or the RGB header! I didn’t use the phantoms bracket (wasn’t room) and found there was just enough room to get it in if I pushed down a little (a lot) on the glass! What a nightmare build, spent...

Thanks, I feel like a retard now. Had the day from hell getting my build done tear the whole thing down trying to find a leak (it wouldn’t pressurise with pressure tested) and then realise it’s because I didn’t have this little extension on the drain port .

If you look at any of the waterblocks there is a really low profile fitting they come with, challenge I have is my water block only came with 2 and I need an extra one for a drain valve. As you say they are slightly recessed but the one in the pic you sent me looked much higher profile and I...

Hi, I got a big ek xl waterboock and it came with the little bit to attach fittings into in the top, however in the bottom there are only ‘plugs’, I tried to put the normal fitting directly into it and it leaks. Which fitting do I need to put in first? I know what it looks like but I can’t find...

I've bought the phanteks mount now so lets see how I get on at the weekend! :)

Oh and those radiators in the top and back are both full size 360 ek PE rafiators. The bottom one is a 360 XE extreme in a push pull config. I have 16 high pressure Corsair hd120 fans on them too (push pull on both the b Bottom and rear rads

It’s an Overclocked 3950x at 4.4 all cores, however I built the system with upgrading to a 32 core threadripper in mind as I may upgrade to that later.