3.6GHZ + C2D clockers please

easyrider · 22 Jun 2007 at 02:03

Would be nice to see who is in the 3.6GHZ+ club Stable.

I'm finding it hard wafting through the " I'm at 3ghz" threads.

Top end clockers please apply

chaparral · 22 Jun 2007 at 03:55

3600ghz here with watercooling....

Can do 3700ghz as in my 3dmark score with a little higher vcore...
http://service.futuremark.com/compare?3dm06=2241549

modo77 · 22 Jun 2007 at 06:20

3.6 here, not tried pushing it any further.

ArchAnGeL · 22 Jun 2007 at 07:19

[email protected] here
10+ hours orthos blend priority 9.
gets a bit flakey above that. 3 hours ish at 3.9 and will run superpi just above 4 gig.

jimmyjimmyo · 22 Jun 2007 at 09:24

6600@ 3.6ghz with only 1.4v in the bios (everest reads it at 1.36v after vdroop).

I was going to push it furthur but summer is nearly here so I don't want the temps to become an issue

Mansize_tissue · 22 Jun 2007 at 10:38

I guess i'm not worthy of this thread (only at 3.4Ghz

) but i'd just like to ask, what cooling is everyone using to get to 3.6Ghz?

Oh and, ArchAnGeL, does it make a difference what priority Orthos is set at?

Azza · 22 Jun 2007 at 10:41

Im at 3.4Ghz though thats only because im on a E6320.

SooTyLaD · 22 Jun 2007 at 11:09

would the people who have the real mint o'cers mind posting their stepping? i'm on the lookout for a good e6600 mine is crap, big time!

(my stepping is L632F btw)

ArchAnGeL · 22 Jun 2007 at 11:35

Mansize_tissue said:
I guess i'm not worthy of this thread (only at 3.4Ghz ) but i'd just like to ask, what cooling is everyone using to get to 3.6Ghz?

Oh and, ArchAnGeL, does it make a difference what priority Orthos is set at?

Apparently, yes. But I'm no expert on the matter. I think higher priorities generate more heat.

ArchAnGeL · 22 Jun 2007 at 11:36

my stepping is L633A554

BubbySoup · 22 Jun 2007 at 12:04

[email protected] under water (lo-flow).

WoZZeR · 22 Jun 2007 at 12:20

3.6Ghz on my Shuttle on water with E6700, it's an early E6700 so shall replace with Quad when the prices drop (the OC is a tad flaky at the moment but working on it, it's a CPU or N/B limited OC I think)

EDIT: All you folks with low VCores are so lucky, mines at +250mv. :eek:

jimmyjimmyo · 22 Jun 2007 at 13:52

QuiKsiLVeR said:
would the people who have the real mint o'cers mind posting their stepping? i'm on the lookout for a good e6600 mine is crap, big time!

(my stepping is L632F btw)

Mine is a L629B I got it from OCUK around november and it is a fantastic chip although it can get a little toasty

chipper36 · 22 Jun 2007 at 14:03

CPU: E6600 L632B861
OC: 3712MHz
Stepping: 6 B2
Week: L632
Code: B861
Vcore: 1.550v Bios - 1.51v Load

Run 24-7 @ 3.6Ghz with 1.45V

Further pics on another thread http://forums.overclockers.co.uk/showthread.php?t=17699083&page=9&pp=30

Mansize_tissue · 22 Jun 2007 at 14:47

chipper36, your rig is air cooled, right?
I can't believe how cool your CPU runs!

Millwall.FC · 22 Jun 2007 at 15:08

e6600, 400 x 9, 1:1 with ram, 1.38v, L629B stepping (brought november last year), water cooled.

pegasus1 · 22 Jun 2007 at 17:13

This thread is clockist,

i think it should be those who have OCed by at least 1.5ghz, then us [email protected] could get a look in

chipper36 · 22 Jun 2007 at 17:50

Mansize_tissue said:
chipper36, your rig is air cooled, right?
I can't believe how cool your CPU runs!

Yes air cooled with a Tuniq Tower and 5 12cm fans to keep everything else cool.
Obviously creates quite a bit of noise but not too much to bother me.
Was thinking of water cooling to get to 4GHz but i find 3.6G enough for my needs.

devablue · 22 Jun 2007 at 20:31

[email protected], L651B731, tuniq @ 60c load, 1.54vcore

MisterT · 22 Jun 2007 at 20:41

E6420 stable up to 3.75 gets a tad flaky there after, just runs s.pi at 3.84:
320W peltier cooled

ran stable at 3.7 with just water but very unstable anything behond that