** EKWB-PREDATOR - AVAILABLE NOW **
- Thread starter rjk
- Start date
blame the tax man for that one guys. I was going to round the prices to the closest number to make the prices look nice but decided to keep them as close to the EKWB suggested prices as my system would allow.
To buy the products included in the 240 Predator [which wouldnt be an all in one pump unit with the rad so you would need a reservoir or fill port anyway]
CPU Block - 34.99
RAD - 59.99
Tubing - 3.49
Fittings - 15.16
DDC Pump - 54.98
Coolant - 5.60
Fans - 23.98
Total 198.19
So realistically, the Predator unit is very cheap for what it is.
To buy the products included in the 240 Predator [which wouldnt be an all in one pump unit with the rad so you would need a reservoir or fill port anyway]
CPU Block - 34.99
RAD - 59.99
Tubing - 3.49
Fittings - 15.16
DDC Pump - 54.98
Coolant - 5.60
Fans - 23.98
Total 198.19
So realistically, the Predator unit is very cheap for what it is.
EKWB are releasing a case compatibility list soon.
Once I get one here, then I will be checking some less common cases for compatibility too.
EDIT*
we have one in the office. I just checked using the measurements that EK have on their press info. It will most likely fit, however you may lose your rear fan as the bulkhead at the end of the rad may make the radiator too long to fit both. there is a few different configurations you could use to make it work so it would work for sure but how well would depend on how creative you got with it. Personally, I would empty the system and cut the tubes down a lot to get it fittings nicer into that case.
Last edited:
I have asked EK to see if they have any updates on this but I can't imagine it is the sort of info they will have to hand yet.
tough one, the rad is a modified version of CoolStream PE so I guess it just uses the screw mounts off that.
In honesty though, I have an EK Rad from years ago that has been installed in about 20 different setups and had countless screws put into the fan mounts without any threading issues.
there are comparisons with major coolers that are comparable to the kraken in my posts in here.
The Corsair h110 is similar enough to give you an idea.
no idea. they are sending review samples out to press as soon as they are available.
the case compatibility list will take some time to compile.
EK are obviously not going to buy every single case on the planet to test so they will just have to generate it over time.
essentially, if you have room in your system for a 240 or 360mm radiator, then you are going to be able to fit a predator cooler in there.
and theres where your post lost credibility.
a properly sorted watercooled computer, configured properly will be quieter than an air cooled PC.
I don't doubt that a carefully considered air cooled system can be quiet. I have one currently, but you have made a sweeping statement that is also false.
apples and oranges.
the triton has its place. so does this.
This is designed to meet two markets:
1. people who are looking to get an AIO that they can expand in future and maybe include a GPU
2. people who know a bit about watercooling and want something compact that they can use to save space and eliminate the need for separate rad/res/pump.
you wouldn't, and shouldn't expect a triton to be able to deal with an extra rad and dual GPUs off its one pump, with a predator, you could do that easily.
the triton is a good product and the performance it gives out for the money is spot on, EKWBs own testing shows this, so it really isn't doing a disservice to the triton, more highlighting its bang for buck.
but there is always a market for people looking for something more high end and EKWB have a great rep when it comes to this.
we offer both products so it really doesnt matter to me, but if I was looking for a cooler, the predator would be on my list simply because of what it has the capability of doing with upgrades rather than what it can do out of the box.
the triton has its place. so does this.
This is designed to meet two markets:
1. people who are looking to get an AIO that they can expand in future and maybe include a GPU
2. people who know a bit about watercooling and want something compact that they can use to save space and eliminate the need for separate rad/res/pump.
you wouldn't, and shouldn't expect a triton to be able to deal with an extra rad and dual GPUs off its one pump, with a predator, you could do that easily.
the triton is a good product and the performance it gives out for the money is spot on, EKWBs own testing shows this, so it really isn't doing a disservice to the triton, more highlighting its bang for buck.
but there is always a market for people looking for something more high end and EKWB have a great rep when it comes to this.
we offer both products so it really doesnt matter to me, but if I was looking for a cooler, the predator would be on my list simply because of what it has the capability of doing with upgrades rather than what it can do out of the box.
i would add a 240 rad into the loop for that configuration
push pull is a total waste of time.
ive said it before, but will say it again.
if you want one of these then I suggest getting your pre order in place.
I have lots on order with EK but I really doubt that our order will be fulfilled in the first hit if worldwide demand for this anything to go by.
At the moment, someone who pre orders will stand a good chance of getting in on the first wave of stock. After this week, well I can't be so sure.
EK are a great company to deal with but have historically been poor in terms of radiator supply. This may be a totally different story but I personally would suggest that the predator will not be available in any large quantities and that a pre order is very much advised to get your place in the queue.
I would also suggest that if there does happen to be free stock available when the stock lands, then it will go very quickly.
as far as I am aware, the shipping date of late september is still the plan for the 240 units. and mid to late october is still on the cards for the 360
if you want one of these then I suggest getting your pre order in place.
I have lots on order with EK but I really doubt that our order will be fulfilled in the first hit if worldwide demand for this anything to go by.
At the moment, someone who pre orders will stand a good chance of getting in on the first wave of stock. After this week, well I can't be so sure.
EK are a great company to deal with but have historically been poor in terms of radiator supply. This may be a totally different story but I personally would suggest that the predator will not be available in any large quantities and that a pre order is very much advised to get your place in the queue.
I would also suggest that if there does happen to be free stock available when the stock lands, then it will go very quickly.
as far as I am aware, the shipping date of late september is still the plan for the 240 units. and mid to late october is still on the cards for the 360
today has been a good post day.
anybody want to know any specifics?
Impressions out of the box:
In all, I am very impressed after just plugging it in and getting to grips with it. It has a lot of little bits that really stand out as being engineered. EKWB have thought this through big time. It isnt just a 'cash in' on the AIO market like some others have done.
Huge kudos to EK for this. They should be applauded and I think the sales will do that on my behalf.
As a watercooling enthusiast and someone that has spent a long time buying watercooling as a job, it takes a lot to impress me. This is the only thing I have seen in recent memory that has done that.
I will try to get some testing done as soon as I can.
anybody want to know any specifics?
Impressions out of the box:
- packaging is spot on. really well presented product.
- the rotary fittings built into the reservoir side are brilliant and allow for a good range of movement of the block
- the tubing is fantastic in terms of wall thickness and bend radius
- the two stepped thread on the block screws allowing for backplate installation as well as 2011 compatibility is simple but genius
- the installation procedure for the unit is perhaps the simplest i have ever seen in an AIO
- the pump is QUIET - I am most impressed by this fact.
- The fans are a bit noisey at full tilt but are actually very quiet once you have your board controlling the noise.
In all, I am very impressed after just plugging it in and getting to grips with it. It has a lot of little bits that really stand out as being engineered. EKWB have thought this through big time. It isnt just a 'cash in' on the AIO market like some others have done.
Huge kudos to EK for this. They should be applauded and I think the sales will do that on my behalf.
As a watercooling enthusiast and someone that has spent a long time buying watercooling as a job, it takes a lot to impress me. This is the only thing I have seen in recent memory that has done that.
I will try to get some testing done as soon as I can.
also as a note.
If you plan on getting a predator, before installation, grab the compression fittings and tighten them with your fingers as much as you can.
they didnt move much out of the box but they are watercooling fittings and as much as i trust ek to have installed them correctly, for peace of mind, I would suggest that all OCUK customers just pinch them tight upon delivery anyway.
If you plan on getting a predator, before installation, grab the compression fittings and tighten them with your fingers as much as you can.
they didnt move much out of the box but they are watercooling fittings and as much as i trust ek to have installed them correctly, for peace of mind, I would suggest that all OCUK customers just pinch them tight upon delivery anyway.
not at all.
all x99 boards have a plastic backing on the socket mechanism to avoid shorting the board.
This is already cut out on some boards like the rampage but is not punched through on others like most of the gigabyte range.
There is an incredibly complex method involved in ensuring compatibility with this and some other aftermarket cooler.
Firstly, you need to purchase an official intel 2011 motherboard enhancement device. You will need to get the flat head type.
Then place your motherboard on a motherboard box and push the official intel 2011 motherboard enhancement device through the holes in the board so that the holes are open.
Once the holes are open, the CPU block can be attached to the board with ease.
The Screws from the block will stick out from the rear of your motherboard slightly
Here, we can see an elite tier hardware user who has carried out this modification.
Wow, you're really not letting this go?
Obviously the use of your eyes and common sense is crucial here. If the board doesn't have holes in it (which accounts for 1/27 boards we have in the office to test) then you can't pop the plastic.
It is only asrock that I am aware of that does this. And they are a scruffy brand anyway.
That dude drilling through his motherboard? Why? Such a retarded move. Just say, it doesn't work rather than brick a board for YouTube views.
Anyway. If there is an issue and you have a board without holes on the rear side, then you could easily use a hacksaw to chop the thinner section of thread off and leave the 2011 compatible section.
It's really not hard to get round it and it really isn't a big deal.
At all.
Last edited:
There is a comprehensive list of measurements for the unit on one of my posts in this thread.