ASROCK X570 TAICHI - THE RYZEN 3000 MOTHERBOARD GIBBO & 8 PACK RECOMMENDS

Woodsta888 · 29 Jan 2020 at 08:52

SoC @1.1v seems to be a must on ASROCK boards. Mine needs it on my Phantom gaming 4. And my RAM needs 1.4v at stock settings 3600 16 16 16 32

faceman123 · 29 Jan 2020 at 13:53

Woodsta888 said:
SoC @1.1v seems to be a must on ASROCK boards. Mine needs it on my Phantom gaming 4. And my RAM needs 1.4v at stock settings 3600 16 16 16 32

same!! my rams 1.4 stock 3200mhz will try soc @1.1 sick of it cold booting to factory defaults.

fizzy · 30 Jan 2020 at 14:03

Well - I got the cold boot issue again last night. I had reverted back to 2.10 when I had issues with later versions before and has been fine since, until last night. Sat there with fans on loud for a bit, rebooted, same again. Got into bios and all options had been reset. Manually set everything back as before and it booted up fine. It's an odd one, don't know what it's started doing it on this bios, unless it's a board fault.

Most on auto with mem on XMP and custom fan profiles.

Woodsta888 · 30 Jan 2020 at 15:21

fizzy said:
Well - I got the cold boot issue again last night. I had reverted back to 2.10 when I had issues with later versions before and has been fine since, until last night. Sat there with fans on loud for a bit, rebooted, same again. Got into bios and all options had been reset. Manually set everything back as before and it booted up fine. It's an odd one, don't know what it's started doing it on this bios, unless it's a board fault.

Most on auto with mem on XMP and custom fan profiles.

Just to check and not teaching you to suck eggs, but when you have save & exited BIOS with new settings - do you go back into the BIOS and save it as a profile?

faceman123 · 30 Jan 2020 at 16:13

anyone got a noisey fan? = ( - Any idea on how ASROCK are for RMA's?

Joxeon · 30 Jan 2020 at 16:29

faceman123 said:
anyone got a noisey fan? = ( - Any idea on how ASROCK are for RMA's?

Have you set it to silent mode in the bios?

faceman123 · 30 Jan 2020 at 16:30

Joxeon said:
Have you set it to silent mode in the bios?

Yeah

Joxeon · 30 Jan 2020 at 16:33

faceman123 said:
Yeah

Maybe worth checking the fan connector as I've seen people on here mention 1 of the 4 pins were bent thus causing it to run at full belt all the time.

Space Monkey · 30 Jan 2020 at 16:52

faceman123 said:
Yeah

I didn't have an option in the bios for the SB fan, so I downloaded the ASRock utility and set it in there, works perfectly

faceman123 · 30 Jan 2020 at 16:57

Space Monkey said:
I didn't have an option in the bios for the SB fan, so I downloaded the ASRock utility and set it in there, works perfectly

oh - ill try this - what are your temps btw?

Space Monkey · 30 Jan 2020 at 16:59

faceman123 said:
oh - ill try this - what are your temps btw?

Under load I think I get about 55-58° but I'm water cooled and I don't have great airflow over the board, what's yours?

(That's with an almost silent profile though, I can get that down if I ramp up the fans)

Edit, I'm on the 2.70 bios

pete910 · 30 Jan 2020 at 19:18

Space Monkey said:
I didn't have an option in the bios for the SB fan, so I downloaded the ASRock utility and set it in there, works perfectly

It's right down at the bottom of the list in the fan section

Space Monkey · 30 Jan 2020 at 19:20

pete910 said:
It's right down at the bottom of the list in the fan section

Mine doesn't have it, it lists all the other fan controllers but nothing for SB?

I'm looking in the bit where you control the fan curve with the graph etc... Is it somewhere else?

pete910 · 30 Jan 2020 at 21:48

Space Monkey said:
Mine doesn't have it, it lists all the other fan controllers but nothing for SB?

I'm looking in the bit where you control the fan curve with the graph etc... Is it somewhere else?

H/W monitor >> Fan config.

Space Monkey · 31 Jan 2020 at 02:21

pete910 said:
H/W monitor >> Fan config.

Thanks, I'll have a look tomorrow, can't remember seeing that?

faceman123 · 31 Jan 2020 at 15:19

Space Monkey said:
Thanks, I'll have a look tomorrow, can't remember seeing that?

Can you disable the software and give this a shot space monkey? My board is the Gaming X ( basically the same board)

Space Monkey · 31 Jan 2020 at 15:40

faceman123 said:
Can you disable the software and give this a shot space monkey? My board is the Gaming X ( basically the same board)

I'll have a look in a bit for you

Space Monkey · 1 Feb 2020 at 13:51

faceman123 said:
Can you disable the software and give this a shot space monkey? My board is the Gaming X ( basically the same board)

Hi mate,

Right, I've disabled the software in windows, so its only the BIOS sorting the SB Fan speed.

It works as described, silent is low rpm, full is loud etc... though I've found with the windows software or the customise option in the BIOS that you can get the fan speed lower than the pre-set Silent option, and of course you can set a fan/temp curve

faceman123 · 1 Feb 2020 at 14:26

Space Monkey said:
Hi mate,

Right, I've disabled the software in windows, so its only the BIOS sorting the SB Fan speed.

It works as described, silent is low rpm, full is loud etc... though I've found with the windows software or the customise option in the BIOS that you can get the fan speed lower than the pre-set Silent option, and of course you can set a fan/temp curve

Thanks a lot space monkey I'm not able to find the software on the website ( found some for a x370 ), yeah the BIOS option is still noisy on full load so good news with the software

Space Monkey · 1 Feb 2020 at 14:30

faceman123 said:
Thanks a lot space monkey I'm not able to find the software on the website ( found some for a x370 ), yeah the BIOS option is still noisy on full load so good news with the software

So when you set the BIOS to silent, it still is loud?

When I made changes within the BIOS screen the fan speed automatically changed, without needing to exit and save.

Have you check the fan connector on the board, a lot of others have had the same issue and it was a wiring problem?