• Competitor rules

    Please remember that any mention of competitors, hinting at competitors or offering to provide details of competitors will result in an account suspension. The full rules can be found under the 'Terms and Rules' link in the bottom right corner of your screen. Just don't mention competitors in any way, shape or form and you'll be OK.

Thermal Paste In AM4 Socket

venomx

venomx

venomx

Associate
Joined
17 Feb 2009
Posts
1,139
I tend to put a fair bit of thermal paste in for good measure and have had excellent results with it.

Only thing is, when I came to fit my new AIO a bit of thermal paste was stuck underneath the CPU in the socket of the motherboard ( the tiny little pin holes )
I used some wipes designed for cleaning CPUs and a tiny bit still remained. However my CPU and temps are fine.

Is that a problem or not ? It's non conductive paste
 
Last edited:
venomx said:
I tend to put a fair bit of thermal paste in for good measure and have had excellent results with it.

Only thing is, when I came to fit my new AIO a bit of thermal paste was stuck underneath the CPU in the socket of the motherboard ( the tiny little pin holes )
I used some wipes designed for cleaning CPUs and a tiny bit still remained. However my CPU and temps are fine.

Is that a problem or not ? It's non conductive paste
Click to expand...
If it works it works, and you’re more likely to cause problems by trying to fix it than you are to clean it fully. It’s always possible that over time it will spread more, but after 6+ months most pastes will start to dry out to a powder anyway.

One question though: plenty of thermal paste?

Less is more man, you only need enough to form a very thin film between the heat spreader and cooler pad.
 
philo-sofa said:
If it works it works, and you’re more likely to cause problems by trying to fix it than you are to clean it fully. It’s always possible that over time it will spread more, but after 6+ months most pastes will start to dry out to a powder anyway.

One question though: plenty of thermal paste?

Less is more man, you only need enough to form a very thin film between the heat spreader and cooler pad.
Click to expand...

Yeah I always get a bit carried away lol. Temps are good though ( 31c idle, 65c stress test )
 
Last edited:
Looking at the description of the paste I used ( and have always used ) says " Contact with any pins will not cause any damage as it contains no metal particles "

In future I'll try and be a bit more conservative with my paste

You will probably laugh but this is how much paste I just used after remounting my AIO for cable management...
Size of a pea... a big pea... :D
20210228-121646.jpg
 
Bouton Aide said:
It's a good job it wasn't Liquid Metal.

https://forums.overclockers.co.uk/t...iquid-pro-thermal-compound-dead-cpu.18063812/
Click to expand...
I has four diplomas in hardware, network and technical support y’know. But I like to bathe my CPU socket in something with the qualities of liquid Mercury.

It’s a classic thread :)


venomx said:
Looking at the description of the paste I used ( and have always used ) says " Contact with any pins will not cause any damage as it contains no metal particles "

In future I'll try and be a bit more conservative with my paste

You will probably laugh but this is how much paste I just used after remounting my AIO for cable management...
Size of a pea... a big pea... :D
20210228-121646.jpg
Click to expand...
I mean... yeah you could do with like 10% of that and your thermals would only improve. But hey, it all works.
 
venomx said:
I tend to use a generous amount otherwise it would bother me thinking I didn't put enough on
Click to expand...

The point of the paste is to fill microscopic gaps between the two metal surfaces. It's not jam in a sandwich.

If the cpu and the heatsink were two bits of paper that size imagine the amount of pvc glue you'd need to stick them together.

That's how much thermal paste you'd need.
 
venomx said:
Next time I'll try to put less on. Everything's running fine now so i'll leave it.
Click to expand...
To be frank most of us have done stuff like this. I once got a bit of thermal paste on the edge of a Socket (775 iirc). I then wiped it with a tissue, which of course got tissue into the socket. I then used tweezers to remove the tissue and pulled out a pin along with the tissue (socket 774 FTW!!).

As I was a penniless student at the time decided to *ahem* just RMA it to Gigabyte, who said 'no error found' but returned a completely new board.
 
You must log in or register to reply here.
Back
Top Bottom