Any obvious ideas about this error i keep getting?

booyaka · 11 Dec 2007 at 18:02

Current system
Q6600 G0
2gb ballistix PC6400
8800GT
Gigabyte DS3R P35

straight in at 3ghz - 8hours prime stable no probs.

However, anything after his starts to get very flakey.

Above 3ghz was 1.35v, ram 1:1 333x9, ram 2.1v (5,5,5,18 loose timings)

Bumping the fsb up to 340 then prime fails in seconds with a blue screen and a full reboot. Can't read the blue screen as it's only there for a second.

When i boots back up i get the following MS error

C:\DOCUME~1\CHRIST~1.000\LOCALS~1\Temp\WERa528.dir00\Mini121107-04.dmp
C:\DOCUME~1\CHRIST~1.000\LOCALS~1\Temp\WERa528.dir00\sysdata.xml

Any ideas? Taken voltage to 1.4v and ram to 2.2v and also put ram speed lower to take that out of the equation but anything over 3ghz and the same thing happens.

eyetrip · 11 Dec 2007 at 18:04

Have tou tried upping the northbridge voltage a notch?

Ben M · 11 Dec 2007 at 18:04

google the code?

booyaka · 11 Dec 2007 at 18:05

ffallic said:
Have tou tried upping the northbridge voltage a notch?

it has been bumped by 0.1v - i think that is the MCH voltage of something on the gigabyte boards

booyaka · 11 Dec 2007 at 19:45

Ben M said:
google the code?

tried and nothing

Cob · 11 Dec 2007 at 19:54

Have you run MemTest at the memorys stock settings (800mhz 4-4-4-12 2.2v)?

DeadMan · 11 Dec 2007 at 19:58

Check the event log for any errors

booyaka · 11 Dec 2007 at 20:35

Cob said:
Have you run MemTest at the memorys stock settings (800mhz 4-4-4-12 2.2v)?

not yet - will do - they are only just back from RMA last week!!

Cob · 11 Dec 2007 at 21:03

Then you'll know why I made the suggestion

booyaka · 11 Dec 2007 at 22:25

Cob said:
Then you'll know why I made the suggestion

indeed - all passed mind you - all tests and ran for 90mins - zero errors

booyaka · 11 Dec 2007 at 22:34

DeadMan said:
Check the event log for any errors

there is errors showing but i'm not sure what really to look for

booyaka · 12 Dec 2007 at 13:20

any more options??

YZFAndy · 12 Dec 2007 at 18:53

My ballistix didn't want to do anything more than than their standard spd setting for the first week of use. I was a bit dissapointed with them, but graduly I managed to push thier speed and timmings a lot harder.
Also seeing as you have had a set go already have you checked they are not getting too hot? For some reason I had disconnected the fan that normally blows onto mine one day and when i touched the heat spreader it almost took my fingerprint off they were so hot.

booyaka · 13 Dec 2007 at 10:26

YZFAndy said:
My ballistix didn't want to do anything more than than their standard spd setting for the first week of use. I was a bit dissapointed with them, but graduly I managed to push thier speed and timmings a lot harder.
Also seeing as you have had a set go already have you checked they are not getting too hot? For some reason I had disconnected the fan that normally blows onto mine one day and when i touched the heat spreader it almost took my fingerprint off they were so hot.

cheers - still have huge issues with pretty much any settings above 3ghz. Getting the original error most of the time!

booyaka · 14 Dec 2007 at 16:10

still getting the BSOD after about 10 seconds of prime95 and a full reboot instally.

tried 400 x 8 and ram on very slack timings etc but again full reset just after starting prime. 1.4volts through the cpu and MCH +0.2, fsb +0.2 and ram +0.4v

Any ideas??

when ram on auto settings (trying to find the FSB max) one of the settings "Refresh to Act delay" is showing 0 - is that right?

DeadMan · 14 Dec 2007 at 16:24

booyaka said:
there is errors showing but i'm not sure what really to look for

Try posting some of the errors on here so we can help you more effectively.

booyaka · 14 Dec 2007 at 17:35

Error code 10000012, parameter1 0000000d, parameter2 00000000, parameter3 00000000, parameter4 00000001.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

booyaka · 15 Dec 2007 at 08:46

right - finally seem to be getting somewhere. It appears that the gigabyte board has horendous vroop when loaded up.

Set it to 1.425v in the bios and when prime loaded on all 4 cores it droops to 1.328 volts.

Slack ram timings for now but primed overnight @ 3.15ghz