Anyone found a WiFi extender with EasyMesh?

richieboy

richieboy

richieboy

Associate
Joined
29 Dec 2004
Posts
2,253
Hi,

I recently got FTTP installed and am looking to improve signal around the house to take advantage of the speeds. I noticed the router I have been supplied (which I am kind of stuck with a bit as ISP won't let me use anything else on a domestic connection) supports 'EasyMesh', which I was hoping to make use of as it would mean the existing router can stay as an AP, and I'd then need two more 'EasyMesh' enabled APs to get signal where it's needed. From a Google around I can't see any obviously available kit that supports EasyMesh, has anyone found/uses kit with it at all?

Obviously I could just disable WiFi on the router and get three mesh APs instead...but am also trying to keep ongoing power usage in mind and so the less devices that need to be on all the time the better! I've already got a modem to power separately now as well as router, where as obviously before with FTTC the modem was built in to the router.

Thanks.
 
It's a local FTTP supplier that has it written in their ToS, from looking about a few users seem to have managed it by obtaining the user/pass from a putty session but I'm trying to avoid that if I can in case it's something they spot at some point in the future and threaten to disconnect me etc!
 
I am looking at other options Armageus- 2.4ghz just about reaches but I was hoping to supply 5ghz to the entire gaff. This is with the current router in prime position in the middle of the house.

I am also a tight git, so am trying to avoid powering any devices unnecessarily - which is why I was hoping to find two 'easy mesh' APs that can work either side of the existing router. It looks like TP Link have WiFi 6 products with EasyMesh (article from Dec 2021) but I don't seem to be able to buy them anywhere yet..
 
Last edited:
As I understand it Easy Mesh is a standard from the WiFi alliance, similar to OneMesh or other proprietary solutions but can be used by everyone, so in theory you could buy any mesh device and it would work with another one (I think). Unfortunately it looks like it came quite late so not a lot of manufacturers have picked it up yet as they have their own...and why give people freedom when you can lock them down to your own proprietary devices!
 
Not sure if you gents have done the maths, but just having a 10w modem and 20w router is now equal to around £10 worth of electricity at around 50p per kWh...I really hope my maths is wrong, but if I add three mesh devices at about 20w each I'd then be paying more just to keep all those devices powered than I would for the FTTP service!
 
Last edited:
WJA96 said:
Yes, and no. 30W worth of appliances running 24/7/365 is about 270kW or £135 per year or a little more than £10 per month so if you meant you're only paying £10 per month for your FTTP then that's very cheap.

And that is absolutely worst case scenario. Typically they don't use their rated power.
Click to expand...
Yeah I was adding three 20w mesh devices on also, so would take it from 30w to 90w, or about £30 a month. Crackers.

Fair point regarding what they use versus their rating... I really hope they don't use the full amount!
 
Caged said:
Ask Trooli if they have a Wi-Fi mesh solution, it's really not acceptable to lock the router down and also offer you nothing to extend coverage if you need it.

The Technicolor mesh device is the OWA0131, see if Andrews & Arnold will sell you one off the shelf. I would advise against spending money on a mesh system that will only work with the Trooli router though, it seems short sighted.
Click to expand...
I hadn't thought about your last sentence. This is a very good point...in which case, if we ignore my post title completely...are there any recommendations for 3 pack mesh systems and I'll disable the WiFi on the router? :D:D
 
I've been looking in to three kit mesh systems, think I'm going to go for the TP link Deco x20 as it's currently at £180 and should do what I need. From reviews it seems that the satellite units all connect back to the primary unit, which would be crap if you were daisy chaining them, but my primary one would be connected to the router in the middle of the house, so hopefully both satellites would connect directly to that one.

I did look at ubquiti but I think I am too lazy for cabling, Poe injectors and the like!
 
Last edited:
Don't get me wrong, I am tempted, but would likely have to do two I'd assume as house is a long rectangle, 16m long by 10m wide over 2 floors. Not sure one AP would cover it.

If I bought 2 of the same UniFi U6 as yourself, used the ports in the back of the router and 2 PoE injectors, does it work as one WiFi mesh or would I need to connect to each AP specifically depending on where I was in the house?
 
Last edited:
Think I'm going to try getting this and running it up to the loft, if that works I'll look at Ubiquiti etc...I did look and ocuk don't sell ethernet cabling so hopefully this one doesn't break any competitor rules:

www.kenable.co.uk

Indoor CAT6 UTP 23AWG COPPER Ethernet PVC Network Cable Reel 50m Grey

50 metres long - 4 twisted pairs (8 wire) 23AWG FULL COPPER Cable Our kenable cat 6 cables are made from a high grade 23AWG copper and are used indoors most commonly for networking although they can be used for sending signals over baluns or even CCTV equipment and are also suitable for POE...
www.kenable.co.uk www.kenable.co.uk
 
You must log in or register to reply here.
Back
Top Bottom