e6300 oc on evga 680i

stinka · 11 Dec 2006 at 12:13

I cant seem to get over 410x7 it wont go any higher, wont boot :confused:

, dropped it back to 1640mhz bus and 820 ddr, ivebeen increasing rated fsb by 10mhz a time in bios. tried slackening to 5-5-5-18 and running ram below 800mhz no good. been runnig unlinked

cpu v core:1.320v

ram 1.1 step
[email protected] 2t

any ideas bit of a noob sorry

any help greatly appreciated, thanks

stinka

clone · 11 Dec 2006 at 12:18

Try a different divider as the board dont like 1:1 very much.

stinka · 11 Dec 2006 at 13:03

clone said:
Try a different divider as the board dont like 1:1 very much.

cheers i'll try that if i can get me head round it

stinka

stinka · 11 Dec 2006 at 14:01

tryed changinging the divider to 3:2 and memoryddr jumped to 1000 +mhz when i f10 and exit it give's the old long beep and nothing so i reset and put it back to 1.1

Just cant seem to get my head round the bios on the 680i have been reading every 680i related post on as many forums as i can find overthe last few weeks, i am happy at 2.87ghz but i would love to get to 3.00 and crack the 6k mark in 3dm06

is my ram up to running high frequencys or am i just setting the bios wrong :confused:

thanks, stinka

VeNT · 11 Dec 2006 at 14:55

e6300s should do 3GHz easly
check your rams getting the right voltages and slack off the timeings a bit (try 5-5-5-18) and or up the voltage.

w3bbo · 11 Dec 2006 at 21:32

I may have missed something here...but did you try increasing the vcore?

stinka · 11 Dec 2006 at 22:19

w3bbo said:
I may have missed something here...but did you try increasing the vcore?

yeh mate ive tried it all the way upto 1.45v in bios it just wont boot at any higher fsb

mercyless · 11 Dec 2006 at 23:52

you might have come across the fsb holes, try 1830+ x 6 or 5 and see. unlinked.

w3bbo · 12 Dec 2006 at 00:06

In the CPU configuration mode have you disabled everything but 'Executive disable bit'?

stinka · 12 Dec 2006 at 19:17

w3bbo said:
In the CPU configuration mode have you disabled everything but 'Executive disable bit'?

just tried this still no good, obviously i still leave core 1 enabled?

going to try lower multi as suggested if i get past the hole do i return to normal multi :confused:

cheers

stinka · 12 Dec 2006 at 19:57

tried both of those its no good cant get past 1640bus/830 ddr mabee thats it for this chip

got cpu fsb on auto will raising this make any diff?

cheers, stinka

w3bbo · 12 Dec 2006 at 20:13

Try raising it to 1.5.

stinka · 12 Dec 2006 at 20:38

w3bbo said:
Try raising it to 1.5.

tried mate still no good, also tried givin it 1.4v cpu v core from 1.35 in bios no good

stinka · 12 Dec 2006 at 21:10

if i put it to like 450 ish fsb it goes to the windows loading screen and the bar moves up and down then freezes so i have to reset, but if i just try moving up 5 mhz on the fsb from 410 where im stuck at and then f10 and save changes it goes into safe mode :confused:

(hope that makes sense)

ive tried dropping ram timings to 5-5-5-15, to acheve that next 5 mhz on bus but no difference

i might just accept defeat

stinka