Had a system running happily for the last year or so and decided to put in some upgrades this week.
Currently have a Q8200, Gigabyte P35-DS3R, 8GB DDR2, Nvidia 9600GT, WD 640Gb HDD, random unbranded PSU and unbranded cheap case.
As said, this worked fine for the last year or so.
Last night I decided to change a few bits and went to the below:
Q8200, Gigabyte P35-DS3R, 8Gb DDR2, Nvidia 260GTX, Crucial M4 128Gb SSD , WD 640Gb HDD, IDE DVD RW, OcUK 550W PSU and Lian Li Alu Case.
System happily booted at first and got into the Windows 7 installer screens but whilst expanding files it would just power off. Checked a few BIOS settings and moved the controller into AHCI mode for the M4 and it now wont clear past the RAID POST screen. Move it back to IDE mode and it goes through but still powers off.
Did a reboot and went to make a drink and came back to it powered off. It had reached the Win 7 install splash screen and then turned itself off again.
After many many reboots it seems that the system just turns off after a set about of time (about 4 minutes) and has to be hard reset.
I put all of the original components back onto the mainboard in the new case and removed the SSD and still the same issue. At this point I think the IDE DVD RW or PSU could be a problem so have bought a SATA DVDRW from the forums which is due soon and I am waiting to agree a deal on a Corsair TX620 PSU from forums too. I even tried a 2nd copy of the Win 7 media but no luck.
Am I likely to have done damage to the mobo with the swapping around? System POSTs without a problem and I have given the SSD to a friend with a Sandybridge setup to connect and run disk checks.
Any thoughts on other likely causes? Will take everything out tonight to check for a short as by the time I thought of that last night I didnt have the energy to pull it all apart.
Currently have a Q8200, Gigabyte P35-DS3R, 8GB DDR2, Nvidia 9600GT, WD 640Gb HDD, random unbranded PSU and unbranded cheap case.
As said, this worked fine for the last year or so.
Last night I decided to change a few bits and went to the below:
Q8200, Gigabyte P35-DS3R, 8Gb DDR2, Nvidia 260GTX, Crucial M4 128Gb SSD , WD 640Gb HDD, IDE DVD RW, OcUK 550W PSU and Lian Li Alu Case.
System happily booted at first and got into the Windows 7 installer screens but whilst expanding files it would just power off. Checked a few BIOS settings and moved the controller into AHCI mode for the M4 and it now wont clear past the RAID POST screen. Move it back to IDE mode and it goes through but still powers off.
Did a reboot and went to make a drink and came back to it powered off. It had reached the Win 7 install splash screen and then turned itself off again.
After many many reboots it seems that the system just turns off after a set about of time (about 4 minutes) and has to be hard reset.
I put all of the original components back onto the mainboard in the new case and removed the SSD and still the same issue. At this point I think the IDE DVD RW or PSU could be a problem so have bought a SATA DVDRW from the forums which is due soon and I am waiting to agree a deal on a Corsair TX620 PSU from forums too. I even tried a 2nd copy of the Win 7 media but no luck.
Am I likely to have done damage to the mobo with the swapping around? System POSTs without a problem and I have given the SSD to a friend with a Sandybridge setup to connect and run disk checks.
Any thoughts on other likely causes? Will take everything out tonight to check for a short as by the time I thought of that last night I didnt have the energy to pull it all apart.

