Good Case for Watercooling

~REALiTY · 23 Mar 2011 at 10:43

Hi Guys,

I need a good case for watercooling, it will have the system in my sig but without the H50

oh and it also needs to have a window

Any suggestions?

Schizo · 23 Mar 2011 at 10:44

corsair 800d.

close thread/

Josh P · 23 Mar 2011 at 11:06

The new XSPC H2?

smit101 · 23 Mar 2011 at 12:15

Silverstone TJ07.

b.cummins · 23 Mar 2011 at 12:33

Silverstone TJ07

zulu9812 · 23 Mar 2011 at 13:28

The TJ07 isn't actually that great for water cooling out of the box - it needs some modding.

joxang · 23 Mar 2011 at 14:08

zulu9812 said:
The TJ07 isn't actually that great for water cooling out of the box - it needs some modding.

Yup. Though you can get them pre-modded from some er...alternative retailers.

Just saw the new XSPC H1/H2....they look amazing!!! Cheaper than importing a mountainmods case too.

mike gunnz · 23 Mar 2011 at 14:47

zulu9812 said:
The TJ07 isn't actually that great for water cooling out of the box - it needs some modding.

Yes and no. It takes a triple/quad rad in the bottom section straight out of the box but requires some work to fit a slim dual in the roof.

smit101 · 23 Mar 2011 at 14:54

Much prefer the look of the TJ07 over the obsidian though.

If you're installing just a single WC loop and want a triple rad in the bottom, then I didn't think the TJ07 required any modding, I believe a quad rad requires removal of the lower drive bays but a triple should fit straight in, drive bays an' all.

Apem · 23 Mar 2011 at 15:06

CM Atcs 840

jinxpad · 24 Mar 2011 at 16:40

I would also have to go with an 800D

Marvin · 24 Mar 2011 at 17:02

Any of these.

OLDPHART · 23 Apr 2011 at 16:31

FT01BW - I'v owned one for 2yrs and l never get tired of it, have had plenty of nice comments of my freinds who are into PC's because of its curves, easy to work on. The rad mounts on the back of the rear of the case, no problems at all.

My case scroll down to you see my name OLDPHART -

http://forums.overclockers.co.uk/showthread.php?t=17305236&page=22

FTO1BW - Case -
http://www.overclockers.co.uk/showproduct.php?prodid=CA-055-SV&groupid=701&catid=7&subcat=

Marvin · 23 Apr 2011 at 16:35

OLDPHART said:
FT01BW - I'v owned one for 2yrs and l never get tired of it, have had plenty of nice comments of my freinds who are into PC's because of its curves, easy to work on. The rad mounts on the back of the rear of the case, no problems at all.

My case scroll down to you see my name OLDPHART -

http://forums.overclockers.co.uk/showthread.php?t=17305236&page=22

FTO1BW - Case -
http://www.overclockers.co.uk/showproduct.php?prodid=CA-055-SV&groupid=701&catid=7&subcat=

It isn't what one would describe as a 'watercooling case' though? As nice as it is, I think when most ask for a watercooling case, they mean all internal, as almost any case can have an external radiator hung outside.

800D, 700D, TJ07, V2000 would be the most obvious cases to spring to mind that aren't stupidly expensive, and require minimal modding.