Haswell Overclock help

Adam Clayton

Adam Clayton

Adam Clayton

Associate
Joined
29 Oct 2013
Posts
6
So i bought a new Motherboard, CPU and RAM a few weeks ago. Went from a Gigabyte EX58-UD5 and a i7 920 to a ASRock Extreme 4 and a 4670K and i picked up some Corsair Vengeance Pro 1600MHz 1.5v.

After a week of using stock speed i went into the BIOS and used ASRocks Optimized defaults for a 4.4GHz which in turn gave me a BSOD every time i tried to boot-up, so i went back to stock and searched online for an over clocking guide i used the one found HERE. I followed that guide and put all my sliders to that what it showed in the pictures and then i did trial and error from then on upping the Vcore by 10 and the CPU cache Voltage by 5 each time it threw me a BSOD.

I finally got it stable-ish and i say ish because if i run Prime95 on Blend it throws me a BSOD after about 10-15 passes but i can play Battlefield 4 for 7 hours (as i did yesterday) with no problems and my temps are only in the range of 60-65 on a load of 100% and 32-33 on idle. I'm running a H100 so i can push it further i just need to know if i have a good 4.4GHz and if i can tune any voltages to get a better Over clock.

I just want to know if i am doing something wrong do i need to change something else. I should also point out that i am using the A-tuning software that is shown in that guide, I use that to find voltages and then when i have good voltages i will put then in the BIOS then i can save that profile and if i ever wish to take the OC off i can just save to a profile and revert back to UEFI defaults. I have to point out that i have only over clocked once before and that was with my old CPU got it to 4.0GHz :cool:.

I shall post some screen shots of what i have in A-Tuning.

gnf6.jpg
aosd.jpg
 
Last edited:
What does VID mean, is it Vcore Voltage or something.

I don't know why i need my system to pass Prime95 maybe because I've been reading on forums that if a over clocked system doesn't pass a stress test then its an unstable clock. Its the reason why i came to this forum as to get a second opinion of sorts. I also have a lot of questions about over clocking.
 
amigafan2003 said:
Yes - vcore. When you load optimised defualts in the bios, what does the vcore default to?



It's only unstable if you crash when you're using you're computer. If you're just gaming and it doesn't crash then it's stable. Who cares if it crashes in prime?

Don't follow what everyone else does when overclocking - find your own path.
Click to expand...

I think it puts it to 1.230 or 1.260. I'll have a look next time i restart, but i think its in that range.

Is my CPU Cache Voltage okay or do i need to lower or raise it. Anything else that i could be tweaking for better over clocking.
 
amigafan2003 said:
No - don't select an automatic over clocking profile in the bios - that will up the voltages (sometimes to a dangerous level).

Select load optimised defaults from the bios save screen and leave everything else as default. What's the vcore?
Click to expand...

When i do that it puts it on Adaptive and Auto.

Hence why i loaded the ASRock Optimized Defaults for 4.4GHz, then played around with it from there, anything below 1.3v and i get a BSoD when running Prime95.
 
amigafan2003 said:
Yes that's fine. On those settings what is the max vcore shown in windows (load up the cores with aida and check with something like cpuz)?

Sounds like you've got a high vcore chip that's not got a lot of headroom for oc'ing. Don't use auto overclock functions - most boards go way over the top on voltages and often get other things plain wrong (like uncore ratio for example).
Click to expand...

in CPU-Z it says at 3.6GHz it goes to 1.149.

With AIDA it goes from 1.0951 V to 1.1243 V, that's sitting at idle.

So as i expected i got a CPU that likes its Volts.
 
You must log in or register to reply here.
Back
Top Bottom