Help with Kingston HyperX

Surveyor · 17 Feb 2012 at 15:30

Subliminal Aura said:
010011000100111101001100001000000100100001100001001000000100100001100001001000000100100001100001

That's the most sense you've made so far in this thread

Subliminal Aura · 17 Feb 2012 at 15:32

Surveyor said:
That's the most sense you've made so far in this thread

I was expecting some HEX back - disappointed

Surveyor · 17 Feb 2012 at 15:47

Subliminal Aura said:
I was expecting some HEX back - disappointed

Life is full of disappointments.

You'll get over it.

Ynot · 17 Feb 2012 at 16:21

OK went for XMP Profile and I think its looking better.

The Voltage was set for 1.5v and it seamed to stay at that even after using the XMP profile.

Surveyor · 17 Feb 2012 at 16:30

Ynot said:
The Voltage was set for 1.5v and it seamed to stay at that even after using the XMP profile.

That's good.

The manual setting of 1.5V seems to have stuck even after you enabled the XMP proifile.

Ynot · 17 Feb 2012 at 16:38

Thanks again Surveyor, I'm more content now.

Surveyor · 17 Feb 2012 at 16:43

You're welcome.

Don't forget that if you get any instability you can increase the DRAM voltage a touch.

Ynot · 17 Feb 2012 at 16:44

Ynot said:
I believe I caused it to happen, I was fitting a network card. I had the PC off but didnt pull out any of the cables (inc power lead) at the back of the PC.

Just out of curiosity, could that have caused the BIOS to go back to default settings?

Ynot · 17 Feb 2012 at 16:44

Surveyor said:
You're welcome.

Don't forget that if you get any instability you can increase the DRAM voltage a touch.

OK, thank you again.

Surveyor · 17 Feb 2012 at 16:51

Ynot said:
Just out of curiosity, could that have caused the BIOS to go back to default settings?

I can't see how that would be the cause.

The BIOS loaded the defaults because it detected a problem with your current settings.

Save your current settings to a profile in the BIOS.

If the problem occurs again you can press F2 or Del to go into the BIOS and load the profile so you won't have to enter every setting again.

You'll then need to take a look at your settings.

Perhaps you need a bit more DRAM voltage?

Perhaps you need a bit more CPU Core Voltage?

It can be a matter of trial and error.

Ynot · 17 Feb 2012 at 17:34

OK Thank you again. I'll see if I can save those settings then.

Thanks so much, really appreciate the help.

Ynot · 17 Feb 2012 at 18:01

Ynot said:
OK Thank you again. I'll see if I can save those settings then.

Thanks so much, really appreciate the help.

Saved the settings (i hope

)

Thanks for the tip.

markymoo · 11 Apr 2012 at 17:39

cbr said:
Hi folks,
would love to hear more on this,
I have the same ram (8gig 2x4) was thinking of another 2x4 to give me 16gig.
But bit worried after reading a lot of things about the voltage and 4 sticks filling all 4 slots may or may not give trouble

Any more thoughts ?

I also would like to know this as when i had my i5 i changed the freq to 1600hz and also overclocked i5 to 4.5ghz but was having crashing problems so when i got my SSD i just left everything at standard. W7 score drops on both CPU and memory from 7.7 to 7.5 and 7.8 to 7.6 respectivly.

Zeed · 11 Apr 2012 at 18:35

Thats how they run on my [email protected] T1 and stable

rossiboy001 · 11 Apr 2012 at 19:32

gigabyte z77 ud5 best suited ram ?

Ignore Posted In Error .