Jonsbo VR3 Mini-ITX PC Case – with PCIe 4.0 Riser Cable
- Thread starter Darren_uk
- Start date
After having the Cooler Master NR200P, LAIN LI Q58, Followed by Ssupd Meshlicious.
Jonsbo VR3 Hands down most Easy to build in,
Space under the Motherboard tray for CPU 8Pin & 24 Pin & did not need Extension cables
PCI-E Cable going into the hole below the motherboard tray
GPU & HDMI Fitting now made so easy.
No more Fiddly Silver GPU Standoffs poles or front rad rails Adjust
No more cables going down the left hand side of the GPU, I did not even need cable ties.
Note: My Arctic Freezer II AIO Rad thickness is 38cm & the Fans 25cm Thickness
So just about got it in front with like 1mm to spare, Also the Hoses at to Face Down
Due to the small footprint of the Case & Design.
Thank you OCUK for top service as always/ Swift Delivery.
Was lucky to get one of the last white Version, before going back to Pre order.
Jonsbo PCI-E 4.0 RISER works fine, PCIE Gen in Bios is on Auto & switched to Gen 4.0 on boot
No artifacts on Desktop or in game.
Good CPU Temp even with rad fans on low rpm,
The Build is Dead silent, Corsair Platinum PSU fan only spins low RPM if the wattage gets to around
350w Usage.
The Main frame slides out from the rear of the outer case frame.
Without the outer Frame on its around the same size of the Meshlicious.
Accessories & Install guide, easy to locate the right Screws to use.
CPU 8pin & 24 Pin Going under motherboard made possible by the tall motherboard standoffs,
No Extension cables needed.
Graphics card now made easy due to the orientation,
Power PCI-E Cables now plugged in from the right & easy to get to GPU Ports being up top,
GPU'S Over 30cm can be mounted by the adjustable PCI Bracket that can move up.
Maybe a draw back to some, Jonsbo I/0 Front panel Type C port is integrated with the USB 3.0 19/20 pin motherboard port,
So may not get full speed like 10GB from a High end External SSD, I am using the Type C on my GPU,
Otherwise would use the Type C on back of motherboard.
CPU 8pin going behind motherboard tray.
24 Pin going behind motherboard tray.
All PSU cables management now made easy.
The case comes with a ATX to SFX Adaptor Plate, I used the one that come with my Corsair PSU.
Jonsbo VR3 Hands down most Easy to build in,
Space under the Motherboard tray for CPU 8Pin & 24 Pin & did not need Extension cables
PCI-E Cable going into the hole below the motherboard tray
GPU & HDMI Fitting now made so easy.
No more Fiddly Silver GPU Standoffs poles or front rad rails Adjust
No more cables going down the left hand side of the GPU, I did not even need cable ties.
Note: My Arctic Freezer II AIO Rad thickness is 38cm & the Fans 25cm Thickness
So just about got it in front with like 1mm to spare, Also the Hoses at to Face Down
Due to the small footprint of the Case & Design.
Thank you OCUK for top service as always/ Swift Delivery.
Was lucky to get one of the last white Version, before going back to Pre order.
Jonsbo PCI-E 4.0 RISER works fine, PCIE Gen in Bios is on Auto & switched to Gen 4.0 on boot
No artifacts on Desktop or in game.
Good CPU Temp even with rad fans on low rpm,
The Build is Dead silent, Corsair Platinum PSU fan only spins low RPM if the wattage gets to around
350w Usage.
The Main frame slides out from the rear of the outer case frame.
Without the outer Frame on its around the same size of the Meshlicious.
Accessories & Install guide, easy to locate the right Screws to use.
CPU 8pin & 24 Pin Going under motherboard made possible by the tall motherboard standoffs,
No Extension cables needed.
Graphics card now made easy due to the orientation,
Power PCI-E Cables now plugged in from the right & easy to get to GPU Ports being up top,
GPU'S Over 30cm can be mounted by the adjustable PCI Bracket that can move up.
Maybe a draw back to some, Jonsbo I/0 Front panel Type C port is integrated with the USB 3.0 19/20 pin motherboard port,
So may not get full speed like 10GB from a High end External SSD, I am using the Type C on my GPU,
Otherwise would use the Type C on back of motherboard.
CPU 8pin going behind motherboard tray.
24 Pin going behind motherboard tray.
All PSU cables management now made easy.
The case comes with a ATX to SFX Adaptor Plate, I used the one that come with my Corsair PSU.
Last edited:
Would think the Temps be same or better since the Jonsbo based off the same frame design as Meshlicious, They made the installing of hardware easy in the VR3 a +
Case outer Shell frame Hole diameter is around 2.5mm, That maybe bigger than the Meshlicious. so another + for air breathing
anti-mavity function - Jonsbo to the Moon ?
My GPU 6800 installed vertically is solid no movement due to the 2 screws on the PCI Bracket & slotted into the Riser cable board.
A Big long GPU horizontal mounted may Shag down, Will not in the vertically position.
Will do some bench marks later running Heaven 4.0 & playing games.
Not sure on Futuremark 3DMark, since the free version is very basic & locked of all the main Benchmarking tell you upgrade/pay.
Case outer Shell frame Hole diameter is around 2.5mm, That maybe bigger than the Meshlicious. so another + for air breathing
anti-mavity function - Jonsbo to the Moon ?
My GPU 6800 installed vertically is solid no movement due to the 2 screws on the PCI Bracket & slotted into the Riser cable board.
A Big long GPU horizontal mounted may Shag down, Will not in the vertically position.
Will do some bench marks later running Heaven 4.0 & playing games.
Not sure on Futuremark 3DMark, since the free version is very basic & locked of all the main Benchmarking tell you upgrade/pay.
Last edited:
The Forum Avatars are auto generated, Avatar May change again once you have a lot more posts/Rank up.By the way, is there any way that I can remove the profile image of the female and replace it with a male, or is that something that must be earned, 'round here?
Ah yep LOL PurrfectBy the way, have you read the paragraph on their product page (as auto-translated--by Edge, anyway)? :|
VR3 black
In response to the "furnace offensive" of CPUs and GPUs, Josper VR3 came into being. Supported by 325mm in-length graphics cards, it is compatible with most mid- to high-end graphics cards. Three-sided iron mesh fresh air and 280 cold row support, let your flood beast docile like meow. Double 2.5 + double 3.5 optional hard disk slot to create "small apartment type large villa". Pull-out structure installation friendly MAX.
Meow & docile Are names of GPU Cards & other things & Being how CPU/GPU run hotter now days "furnace offensive"
China Love their Names branding.
My room temp was 30.3c ,
I tried a good Top down CPU air cooler Big Shuriken 3 Scythe with 2 x 120mm fans on front blowing out & temps was really Toasty, Motherboard/system temp 68c .
so AIO way to go like the Corsair Hydro Series iCUE H100i Elite CAPELLIX 30mm thickness.
NOTE: My Arctic Liquid II 240MM AIO really hard to install due to the 38mm thickness of the rad.
Installing a GPU like 3070 ti /3080 3090 Going to push case Temps up a lot. But are fine under load around 66c AMD 6800 & Tested the 3070TI gamerock 3 slot card Temps reached 76c.
basically it come down to the components you install = outcome on Temps.
Last edited:
Will post GPU Temps later on, been very busy on other matters.Depends on the CPU in use. (In my experience.) (But that's a debate for another day; I'll settle for exhaust GPU temps, if you're game.)(Then again, the speed of the AIO fans is relevant. How about on full-blast, thus best-case?)
Here you go, AMD REF-6800
Room Temp 25.1C
144Hz Enabled
Desktop Idle Temp
Heaven benchmark 4.0 Under load - Score 4500
-------------------------------------------------------------
AMD built in stress Test
Running the stress test for 60s
Room Temp 25.1C
144Hz Enabled
Desktop Idle Temp
Heaven benchmark 4.0 Under load - Score 4500
-------------------------------------------------------------
AMD built in stress Test
Running the stress test for 60s
I did a quick benchmark of the Front / Top I/O USB 3.1 Type C port
Crucial x6 2tb portable SSD storage
Using the top case Type C very Poor performance due to using the 19/20 pin USB 3.0 port
Using a proper Type C 10GB from back of Motherboard or GPU
This is the max read & write spec of the Storage Spot on
Crucial x6 2tb portable SSD storage
Using the top case Type C very Poor performance due to using the 19/20 pin USB 3.0 port
Using a proper Type C 10GB from back of Motherboard or GPU
This is the max read & write spec of the Storage Spot on