Koolance QD3 Quick Disconnect help

[syfer1987]

Hi i need some help in picking QD3 Quick Disconnect.

Here is the setup
2 on the bay res
2 on the radiator
2 on the cpu block
2 on the gpu
I need Threaded G 1/4 so that i can directly fit them to bay,radiator,cpu block and gpu.
But i am stuck not sure in what to get?

I might even need an few angle ones to and must match the other QD3.

I am not sure in what to buy need help.

Me be if some can help pick some parts i would be great full.

 

[Uncle Petey]

You sure you need one on every component?

What size tubing are you using?

Maybe it's better if you post a pic of your rig. Then we might be able to find a better or at least cheaper solution

 

[syfer1987]

ok ill post later im busy just know

 

[pre]

You will not want a pair of QDCs between everything. Depending on your loop setup a pair before your CPU block and after your GPU blocks should give you enough flexibility if you want to upgrade regularly.

That said if you want to have a quick disconnect pair screwed into an inlet (or outlet) of a block you will most likely want a QD3-MG4 (which has a 1/4 bspp thread) and a QD3-F13X19 (for 13mm (1/2") ID tubing). The MG4 pair will screw into things like this if you need an angled connector going in or out.

If you want to have a pair between tubing you will want a QD3-M13X19 and a QD3-F13X19.

Be careful when ordering - lots of places don't stock both the male and female parts or just sell one and don't have the stock number listed on their webpages.

 

[syfer1987]

the case will be
caselabs magnum-tx10-v and the radiator will be at the top chamber.

The radiator i have picked is
Phobya Xtreme SUPERNOVA 1260 Radiator

Dual Drive Bay Reservoir
Monsoon Series Two Premium Dual Drive Bay Reservoir for One Laing D5 Pump with Quick Change LED : Black / Red
Yes I want hreaded G 1/4 on every component.

need some help in Koolance QD3 Quick Disconnect help setup which one will go where.

here what im thinking

I will fit
QD3 Male Quick Disconnect No-Spill Coupling, Male Threaded G 1/4 BSPP
SKU: QD3-MG4
on all of the pc parts.

Then on the Bay Reservoir i will fit 2 QD3 Female Quick Disconnect No-Spill Coupling, Compression for 10mm x 13mm (3/8in x 1/2in)
SKU: QD3-F10X13.

On the cpu block i will fit 2
QD3 Female Quick Disconnect No-Spill Coupling, Angle Compression for 10mm x 13mm (3/8in x 1/2in)
SKU: QD3-F10X13-L
so that it will then go to the gpu.

First GPU block will have fit 1 QD3 Female Quick Disconnect No-Spill Coupling, Compression for 10mm x 13mm (3/8in x 1/2in)
SKU: QD3-F10X13 then i will use sli bridge the gap and then the second gpu i will use 1 QD3 Female Quick Disconnect No-Spill Coupling, Angle Compression for 10mm x 13mm (3/8in x 1/2in)
SKU: QD3-F10X13-L
which will go back in to the Bay Reservoir.

Bare in mid that first thing i would do is put QD3 Male Quick Disconnect No-Spill Coupling, Male Threaded G 1/4 BSPP
SKU: QD3-MG4
on all of the pc parts.

What do you think am i correct in this or did i do something wrong??