New build problems, please help!

Yucca

Yucca

Yucca

Associate
Joined
20 Nov 2004
Posts
2,209
Location
Nock/Leicester
Hi all, need some help with my new build. I used to have the pc in the sig below. I wanted to upgrade the gcard so i have brought a new dfi expert mobo and a 7900GT. I stripped the pc down, cleaned it all, and have now rebuilt it with the new mobo and gcard.

I was originally using 2 hard drives, 1 36gig raptor and a 300 hard drive as storage. But i know the raptor has bad sectors because in the past when i have formatted it i have to leave about 5 gig unpartitioned else windows goes mad! So i thought id ditch the raptor and just use the 300 gig.

I got it all up and running, installed windows no problem and begain installing the mobo drivers. Windows froze! I restarted it but it did it again a few mons in! I tried a reformat but that hasnt helped.

I thought id try the raptor as maybe the 300gig is damaged but thats giving me the same problems.

So what do i do now?! :(
 
Admiral Huddy said:
.. I'm wondering if your new motherboards memory settings are incorrect? Make they the are set to auto/SPD or to the recommended settings.
Click to expand...

There set to T1 2-2-3-6. I know the ram can do 2-2-2-6 so it should be ok. Its running at 200mhz to, so thats ok aint it?
 
Stelly said:
check that everything is seated right... then check that the connection between the HDD and the MB is ok... are you using SATA??

Stelly
Click to expand...

Yes i am using sata, using port one on the mobo. I have checked the wire and its ok. I could try a new lead a suppose, but windows works fine untill it freezes.

What do you mean by everything seated right? Shall i reseat the cpu? I didnt think the problem i am getting could be cpu related?
 
I dont know what it is to be honist. I originally had the ram in the two yellow slots but i have moved them to the orange now. Still same problem though.

I have noticed that in the event viewer under system there are millions of errors called cdrom. The properties say there is a driver error.

Could the controller on the mobo be naff?

Shall i try reinstalling windows from sata5 instead of sata 1 as i think its on a different controller isnt it?
 
Ok, ive pulled one stick out and booted into windows and left the screensaver running (normally freezes on that to). So hopefully i will know in the next 10 mins if it is the ram stick that i have pulled out thats giving me grief.

On a side note, 512 ram! Been a while since i have seen that i my rig! Looks odd! :p
 
Wait a minute.... When i install windows, should i have pressed f6 and gave windows the sata floppy that came with the mobo?! :rolleyes:
 
Stelly, yea i think there is 4 controlled by silicon image and 4 by nvidia. I tried sticking the cable into port 5 rather than one and the pc didnt even recognise that a hd was connected?!

But then you all said forget playing about with that and try the ram thing so im doing that now. Been 5 mins and all is ok so far. Report back in 15 mins! If it holds out, we may have found the problem!

Guna cost me more money though! :(
 
It froze! Going to try the second stick now! No i havnt tried memtest but what i am doing now should tell me its the ram if it is shouldnt it.

The ram was fine a few days ago in my old mobo so i think it has somthing to do with the board tbh.
 
Ok the memory didnt make any difference at all. I am going to try and use a different sata port now see if that helps.

If not, im guna pop down my mates and try an ide drive.

Dont really wana flash the drive cus 1) might have to send it back 2) For the ammount of money i have spent on the mobo, it should work!
 
Ok if i put the hd on sata port 5,6,7 or 8 its not even recognised!

So what else can i do now? RMA time? Or shall i rebuild my old mobo, gcard and try that?
 
You must log in or register to reply here.
Back
Top Bottom