project:20 (parvum resize)

[shadowscotland]

Aim (primary)

Reduce the size of the Parvum S1.0 case I won to a more manageable 20 litres
But keeping the mATX mobo, full size psu, double rad and duel gpu's.

The secondary aims inclued
Complete the build in less than one week (prevous build logs I've made have dragged on - sorry)

Ok let's start off with some photo's I took a few weeks back and posted in the compertition thread linky
The S1.0 is quite big for a SFF Matx case (35L). Shown here with a PC Design Labs QMicra V2 (29L cube), and Silverstone TJ08B-E (30L)

 

[shadowscotland]

To win the comp I made a to scale card model of the S1.0
And this is what I used to mock up a few of my designs

Template

The one at the front was my first attempt with blue tac corners.
The one behind was the finished model, now water damaged

The four designs that progressed to models behind the S1.0 - from left to right.
1) Psu / HHD chamber as per S1.0 - no cards
2) Window panel acting as two walls - separate rad chamber to front
3) as 1 but with cable zone at rear. When in use it would stand on rear panel
4) Mobo zone as per S1.0 - psu over cpu, rad to front

Reverse view - cable zone cover cut away to show I/O etc

Designs 1 and 3 are approximatly 35% of the S1.0 and although I had no plans on adding a card to my trinity system I wanted the flexablity of swapping back to intel.

Design 2 with a 1:5 scale FM2A75 Pro-4
I really liked the concept of the 'angled' window panel but didn't think I had the skill to make it look right

The offset rear panel is to allow for it to stand up with all the wires pointing down.
But in the end I wanted to keep as many pre drilled holes as possable (for speed and ease)
so I kept the rad as forwards facing. I may do a rev2 at some point with a rotated layout but that for another time.

With scale PSU, RX240 and D5-res-top
Cables and HHD in area behind mobo tray

 

[shadowscotland]

One of the Parvum system cubes - and the 2mm machanical pencil lead I used to mark the drill hole.

3mm and 5.5mm drill bits - to match the stock countersinking

After a good hour working out final dims I could have made the motherboard area a little thinner but the extra works imho wouldn't have been worth it.
So I decided on a 30mm clear zone behind the mobo tray and cut down the tray to fit.
This matched up nicely with the spacing required for the rad, happy days .

Psu cut out. Alined with the top of the case for max space for cards in top slot
And minimal overlap to cpu block (45's still required but not 90's)

Inner rear panel cut down and test fitted - more fileing / sanding untill near perfect.
Side panel also complete, and a cut out in the mobo tray to accomadate a corner cube
Base panel and window are still full size at this point.
Infact keeping the base full size really helped - it was drilled three times to accomadate 3 cubes.
With lot's of dim checks, separating, 3mm drilling rebuilding and checking.
Minor adjuctments as required and final countersinking (in correct place) and rebuild.
I did take time but worked.

From the other direction

Psu test fit

Outer rear panel cut and sanded to shape
I'm thinking of asking the parvum guys to cut me a custum rear panel for a 'cleaner' look
But tbh I like the juction and may add some USB ports in the old psu cutout.
This is where I stopped on the first day (school run stops play)

 

[shadowscotland]

Where did you get that qmicra???

I swapped it for a FT02 with one of the members here - MM is a great place to find old school classics

im excited to see how it's going to look.

stay tuned - I finished the major building work last friday, just uploading the photo's and writing the build today / tomorrow

Im confused as to what the point of this is - was it a competition to mod a parvum case? or do you actually need the case to be smaller for your own use?

The competitions first prize was to win a S1.0 (linky) - When it arrived I thought it was too big so I made mine smaller.

hope that answers your questions on with the build

 

[shadowscotland]

Day 2 started with me buying a full size hack saw (everything above was with a junior hacksaw and drill )
My build started with me useing the wrong drill bit, and chipped the front panel when countersinking
Then my camera died too much acrylic dust so I wasn't a happy bunny.
This shot of the cutout for the psu power cable is the only true shot of the build half way through.

These next shots are all post completion - deconstruction images
(after cleaning out my camera)
Hope they make up of the 'missing' action shots.
If not scroll to the next post

Outer front panel - inclueing offcut

Inner front panel

Both panels attached - added a chamfer detail to the corner so the gold panel is visable.

Window panel and cable tidy (bottom left more on this later)

Window panel in correct orientation (arch)
Bit of a break from the norm but works well imho in this small case with it's butt joints.

Inner rear panel inc metal insert cut to accommodate psu

Outer rear panel, with power cable/switch cutout

Rear panel (reverse) assembled with additional psu support (white 'L')
The weight of the psu distorted the panel when it wasn't fully secured on all sided,
so I added the extra piece to stop the panel twisting.

Side panel - just a simple cut down

Motherboard tray - Right hand edge has been cut top and bottom for cubes
The top two holes have also be joined to make an oval for the anti-vandal switch

Top panel - grills centred and cut both sides, unused cable tidy to left.
Might get a blank top from the Parvum guys for a cleaner look but this will do for now

Base Panel, psu support made from offcut - final panel slightly larger than half the original.

 

[shadowscotland]

i KNEW IT!

snip

- and thanks

 

[shadowscotland]

Construction a-go-go

Base and cubes

Motherboard tray

HDD - need to get some velco

Front and side panels added - as are the sata and anti-vandel switch cables.

Anti-vandel switch passing through 'oval' cutout in tray.
You can also just make out the motherboard tray has a double chamfer (see reflection)
so it slots perfectly between the front and side panel.

Inner rear panel attached (counter sink for the win)

Outer panel (and metal insert) on

Rear panel complete (inner view)

Window in and corner detail

This was my first try at a cable tidy - but cut to much away, shame as I wanted the keep the 'PARVUM'

Second go at a tidy

 

[shadowscotland]

Sorry for the poor focus - will redo these on a brighter day (or take the case out into the garden)

I added an window under the grill in the main section (to stop air short circuits) but still allow air to the HDD

I know a modular psu would be neater - but I'll tidy it abit more after I've added the Koolance loop.

That's all for now - it's up and running with the stock AMD cooler but I'll try and install the loop this week

Final dims are 217 x 305 x 350 (WxHxD) or 20.186 Litres so just over target

 

[shadowscotland]

Time for an update.

Spacial testing

Lang D5 vario
Koolance CPU-370
Koolance Pump top (COV-RP450)
Koolance Reservoir tube 60x50mm (BDY-TK050)
Koolance Reservoir base (COV-TKBTM)
XSPC RX240 or Koolance 140mm (HX-CU1401V)
XSPC tube
Various Bitspower and Thermalright acetal 90's
Primochill metal ghost barbs 1/2"

I sorted the loop out in my head but with a case this small it was pointless picking fitting and cutting tube untill it was layed out inside the case.

The basic idea was the RX240 would be at the front, the pump suspended between the psu and rad.
The Radiators barbs would need to be at the top to max space around the PCIe slots.
The Rad would then feed into the side of the res top - barb to barb
Directly down through the reservoir into the pump and out to the block.
Finally from the block back up into the radiator.

First issue was the reservoir side ports were on the wrong side
The next issue was the nearside top port was to close!
So rotating the pump/res I used the far side via an acetal elbow and male/male fitting.
This now ment the outlet for the pump was pointing at the motherboard.
I'm not a big fan of 90's but I needed to use another 2 to make the connection to the block.
And a forth 90 out of the block so the tube didn't foul the res
My only consolation is that with the total tubing lenght being only 25cm I've offset any flowrate drop.

The mix of 90's is due to spacings more that design.
I wanted to use all acetal elbows as it matches the cuboid case and Koolance pump accessaries.
But they didn't always stop in the right orientation - Bitspower rotaries solved that issue
I may swap them all out but for a 24h leak test it will do

Reverse view

Looking towards rad

Normal view (infocus this time)

Looking up at the base of the pump. Twin set of 90's needed

Looking down on pump - I proped the rad to show their relationship inside the case

Leak testing underway

 

[shadowscotland]

Thanks for the comments guys

I've been making stuff with paper for years - black belt in origami me.

And yes it is a nice case but not a great case.
There are major sound isolation issues
It have no front usb or optical drives.
HDD caddies can't be used.
It's also to big imho - and hence the build.
What the S1.0 does have is lots of modeling oppertunities.
It's easy to cut/drill - It's constructed with cubes and butt joints (easy to reproduce)
Designed and build by guys that actively encourage mod's to be done.

Yes I could get the Parvum guys to cut me some panels (I may do this)
But as Chrisbes said - where is the fun in that!
It's cost me nothing (except a hacksaw) and I'm sure the Parvum guys are watching with intrest what I'm up to.

No leaks to report

 

[shadowscotland]

The 'cubes' are really quite something - they come with the case and have fixing holes on all 6 sides

When through 3 junior hacksaw blades on the first day - the full size blade still has a bit of life in it (was a quality bi metal one)

 

[shadowscotland]

Thanks guys - I did it all with hand tools.
With some care and attention anyone could do a build like this (or better as I messed up a few counter sinks)

It's been half term this week so not been able to do much.
But my little man is out with the grandparents all day today so here an early update
(and something to look at while we all wait for the parvum guys ITX build)

There has been no leaks during the last week of testing so time to put it all together.
A10-5800K / FM2A75 Pro4-M / Gskill Ares

Back plate with some old Danger Den thumb nuts and rods

Washers and locking nuts (again from my bits box)

Aligning the 370 AMD top plate

Washers (bits box again - don't want to scratch the block) with the stock springs and thumb nuts on top.

Looking down - all that work on the cable tidy now pointless
But used the space between the rad and motherboard tray to hide the pcie cables

HDD and SSD.
Lian li cable bracket to help with the snakes nest

Top view with the side panel back on. Fill line needs a better stopper

Loads of room, and the only fan in the build

A few shots of the near finished case (front ports and internal tweeks still to do)

Edit:
Just looking at the outside shots again I didn't align the top correctly, Doh! - will sort that out later.
Furmark running 40c cooler that the stock AMD HSF atm happy days