Associate
- Joined
- 4 Jun 2010
- Posts
- 1,279
Hey guys!
This is just a small build log of my new watercooling, specs are
I5 750 3.8ghz - EK-Supreme HF EN Nickel
Asus NGTX570 - EK GTX580+ EN nickel plexi
EK-Multioption RES X2 - 250 Advanced
Silver Kill coil
AlphaCool Laning D5 Vario -EK-D5 X-TOP - Acetal G1/4 Rev.2
Mayhems dyes - Blue
Lamptron Fan Controller
Corsair HX750W
This is the watercooling parts all laid out on the table.
I took the side panel off my 700D and found LOTS of dust
Started off by removing some fans. Which also had quite allot of dust on, so I gave them a clean becouse I will reuse some.
The dust filter was clogged right up with dust so I took that outside and gave it a shake!
Lots of dusty fans!
Rear of the Alphacool Laning D5.
New pump top!
Started unboxing the watercooling...
Fan controller in. Not sitting flush just yet though
CPU cleaned.
SR-1 360 goodness
I had to cut the corners off some of my fans to make them screw down onto the rad as the screws I recived with it where too small.
Rad mounted
Removed the cooler from the ASUS GTX570
All cleaned up!
Block mounted!
and. backplate mounted!
Getting there slowly...
New PSU!
Started tubing it up..as you can see I had to move the pump as it would not work where I orginally put it.
Preparing for leak testing
ooooooo its blue!
Blue mayhems dye going through the block!
it looks soo nice!
Pretty picture!
bubbles!
All finished!
Pretty picture again!
Temps are:
CPU IDLE: usally between 29-33 degrees
GPU IDLE: between 25-29 degrees
CPU LOAD:50-54 degrees
GPU LOAD: Havn't tested yet
Thing to do:
Case window
Blue lighting
Braiding
This is just a small build log of my new watercooling, specs are
I5 750 3.8ghz - EK-Supreme HF EN Nickel
Asus NGTX570 - EK GTX580+ EN nickel plexi
EK-Multioption RES X2 - 250 Advanced
Silver Kill coil
AlphaCool Laning D5 Vario -EK-D5 X-TOP - Acetal G1/4 Rev.2
Mayhems dyes - Blue
Lamptron Fan Controller
Corsair HX750W
This is the watercooling parts all laid out on the table.
I took the side panel off my 700D and found LOTS of dust
Started off by removing some fans. Which also had quite allot of dust on, so I gave them a clean becouse I will reuse some.
The dust filter was clogged right up with dust so I took that outside and gave it a shake!
Lots of dusty fans!
Rear of the Alphacool Laning D5.
New pump top!
Started unboxing the watercooling...
Fan controller in. Not sitting flush just yet though
CPU cleaned.
SR-1 360 goodness
I had to cut the corners off some of my fans to make them screw down onto the rad as the screws I recived with it where too small.
Rad mounted
Removed the cooler from the ASUS GTX570
All cleaned up!
Block mounted!
and. backplate mounted!
Getting there slowly...
New PSU!
Started tubing it up..as you can see I had to move the pump as it would not work where I orginally put it.
Preparing for leak testing
ooooooo its blue!
Blue mayhems dye going through the block!
it looks soo nice!
Pretty picture!
bubbles!
All finished!
Pretty picture again!
Temps are:
CPU IDLE: usally between 29-33 degrees
GPU IDLE: between 25-29 degrees
CPU LOAD:50-54 degrees
GPU LOAD: Havn't tested yet
Thing to do:
Case window
Blue lighting
Braiding
Last edited:
