Last year we brought in Raspberry pi and we've seen it do pretty well having sold some 500 units over the year I have decided to expand the offering beyond Raspberry pi.
View the full range here
RPi Display 2.8" TFT Touch Screen for Raspberry Pi Model B+ @ £34.99 inc VAT
Extend your Raspberry Pi Model B+ with a 2.8" full color display (320×240) with touch panel. There is a framebuffer driver available for this display, so you can use it right out of the box.
This screen has a resolution of 320×240, 3 tactile switches on board, a PWM dimmable backlight and even breaks out the 40 pin GPIO header using an FFC cable so is perfect for any application.
Specification:-
- TFT-Display: 2.83", 240×320 (Transmissive)
- Viewing area: 43.2 x 57.6mm
- Touch Controller: TI ADS7846/TSC2046
- Backlight dimmable (PWM)
- Interface: SPI (Touch Controller + Display)
- 3 tactile switches
- GPIOs available via 40 pin FFC/ZIF-Connector
- Power: 5V
- Raspberry Pi Model B+ Pinout
- Fully assembled
Only £34.99 inc VAT.
ORDER NOW
HiFiBerry DAC+ – Phone Jack Version @ £29.99 inc VAT
Improve your sound! HiFiBerry DAC+ – is a high-resolution digital-to-analog converter for the Raspberry Pi Model A+/B+ and 2B. This is a special sound card for the Raspberry Pi, that is optimized for one specific use case: the best audio playback quality.
This is the phone jack version (there is also an RCA version) which will give you the smallest DAC that is available anywhere. The phone jack is mounted on the bottom of the board for minimal height. This version will fit into many existing Raspberry Pi cases. You just have to drill a hole into the case where the jack is located.
This is still a line-output and not designed to drive headphones. For the use with headphones you will need an additional headphone amplifier.
- Dedicated 192kHz/24bit high-quality Burr-Brown DAC for best sound quality.
- Hardware volume control. You can control the output volume using “alsamixer” or any application that - supports ALSA mixer controls.
- Connects directly to the Raspberry Pi, no additional cables needed.
- No soldering required – comes as a pre-fabricated kit. You just plug it onto the Raspberry Pi B+, conform to the Raspberry Pi hardware-attached-on-top (HAT) specification. Mounted in less than a minute.
- Compatible with Raspberry Pi Model A+, B+ and 2B
- Directly powered from the Raspberry Pi, no additional power supply.
- Ultra-low-noise voltage regulator for optimal audio performance.
Available with different output connectors:
RCA or 3.5mm phone jack.
- Integrated EEPROM for automatic configuration (with write-protection). Note that this feature is still in development by the Raspberry Pi foundation. You will be able to upgrade your HiFiBerry DAC+ when it is officially available. The sound card already works without this feature.
- Comes with all components required to mount it. We include 4 M2.5x12mm spacers to fix the board onto the Raspberry Pi.
*Notice about the compatibility with Raspberry Pi Model A and B: This board is only compatible with the new Raspberry Pi Model A+, B+ and 2B. If you have an older Raspberry Pi, please use the HiFiBerry DAC.
Only £29.99 inc VAT.
ORDER NOW
8GB Micro SD – Samsung Pre-Loaded with NOOBS (Official Card & Adapter) @ £7.99 inc VAT
This Official Micro SD Card Bundle for the Raspberry Pi consists of a Samsung Class 6 Micro SD card pre-loaded with the Official Raspberry Pi NOOBS (New Out of Box Software) package, and a beautifully screen printed Micro SD card adaptor with the Raspberry Pi logo! Simply plug this SD card into your Raspberry Pi, and on first boot you will be given a choice of six recommended Raspberry Pi Operating Systems, including:
- Archlinux – A Lightweight and Flexible Linux Distribution
- OpecELEC (Open Embedded Linux Entertainment Center) – XBMC Media Centre OS.
- Pidora – A Fedora Remix optimized for the Raspberry Pi
- RaspBMC – A Linux Distribution Based on Debian that brings XBMC to your Raspberry Pi
- Raspbian – The recommended OS, which contains LXDE, Midori and Development Tools
- RiscOS – Designed in Cambridge, England by Acorn. Released in 1987, it’s a little bit of history!
A note on SD card nomenclature. The card we’re offering here is rated as Class 6 – in some metrics, Class 6 means slow. This is not the case with this card, which has outperformed many Class 10 cards in our tests – classification seems not to correlate well with random read/write performance. Samsung’s unusual focus on random-access performance on their SD memory means that this card performs very fast and very reliably: we think you’ll be pleasantly surprised!
The Samsung 8GB NOOBS Pre-Loaded Micro SD Card & Adaptor Features:
- Superior Random-Access Performance – Perfect for the Raspberry Pi
- Safe from X-rays and magnetic fields
- Reliable shock-proof technology
- Water and dust proof, thanks to EMC coating
- Tested and proven to last up to 24 hours in sea water
- Capacity : 8GB
- Weight : Approx 0.2g
- Operating Voltage : 2.7 ~ 3.6V
- Speed Class 6
Only £7.99 inc VAT.
ORDER NOW
HiFiBerry Amp+ @ £60.00 inc VAT
The HiFiBerry Amp+ is a high-quality, highly efficient Class-D power amplifier for the Raspberry Pi. Mount it onto the Raspberry Pi model A+, B+ or the new Raspberry Pi 2B and you have a stereo audio system. You only have to connect your loudspeakers. It is the ideal building block for multi-room audio installations.
- Class-D amplifier with up to 2x25W output power.
- Capable of driving 4 Ohm speakers.
- Fully controllable from the Raspberry Pi.
- 44.1kHz and 48kHz sample rates.
- Digital-analog conversion included, no need for external DACs or sound cards.
- Fully digital sound path for optimal audio performance.
- Connects directly to the Raspberry Pi, no additional cables needed.
- Integrated voltage regulator for the Raspberry Pi.
- Only one 12-18V external power supply needed for both AMP and the Raspberry Pi, no need for a USB power supply as well. We also stock a suitable 12V PSU and 18V PSU in our store.
- Comes as a pre-fabricated kit, just plug in onto your Raspberry Pi A+, B+ or 2B. The necessary spacers are already included!
Only £60.00 inc VAT.
ORDER NOW
HiFiBerry Case+ for DAC+ (RCA) and Digi+ – Black @ £11.99 inc VAT
A laser-cut case for the Raspberry Pi Model B+/2B and the HiFiBerry DAC+ (RCA version) or Digi+ made from clear acrlyic plastic.
Note that this case is not compatible with the the Raspberry Pi Model A/B and the HiFiBerry DAC or Digi. Use the HiFiBerry case for these boards. The Model A+ will fit inside, but it will not be a particularly sturdy fit.
Only £11.99 inc VAT.
ORDER NOW
HiFiBerry DAC+ – RCA Version @ £29.99 inc VAT
Improve your sound! The HiFiBerry DAC+ is a high-resolution digital-to-analog converter for the Raspberry Pi Model A+/B+ and 2B. This is a special sound card for the Raspberry Pi, that is optimized for one specific use case: the best audio playback quality.
This is the standard version which uses RCA connectors that you know from your normal stereo equipment (there is also a phone jack version). You can use any RCA cable you like. You can even add a phone jack onto the board (you have to solder it by yourself).
Dedicated 192kHz/24bit high-quality Burr-Brown DAC for best sound quality.
Hardware volume control. You can control the output volume using “alsamixer” or any application that supports ALSA mixer controls.
Connects directly to the Raspberry Pi, no additional cables needed.
No soldering required – comes as a pre-fabricated kit. You just plug it onto the Raspberry Pi B+, conform to the Raspberry Pi hardware-attached-on-top (HAT) specification. Mounted in less than a minute.
Compatible with Raspberry Pi Model A+, B+ and 2B
Directly powered from the Raspberry Pi, no additional power supply.
Ultra-low-noise voltage regulator for optimal audio performance.
>Available with different output connectors: RCA or 3.5mm phone jack.
Integrated EEPROM for automatic configuration (with write-protection). Note that this feature is still in development by the Raspberry Pi foundation. You will be able to upgrade your HiFiBerry DAC+ when it is officially available. The sound card already works without this feature.
Comes with all components required to mount it. We include 4 M2.5x12mm spacers to fix the board onto the Raspberry Pi.
Notice about the compatibility with Raspberry Pi Model A and B: This board is only compatible with the new Raspberry Pi Model A+, B+ and 2B. If you have an older Raspberry Pi, please use the HiFiBerry DAC.
Only £29.99 inc VAT.
ORDER NOW
HiFiBerry Digi+ – Standard Version @ £29.99 inc VAT
The HiFiBerry Digi+ is a high-quality S/PDIF output board for the Raspberry Pi model A+/B+ and the new Raspberry Pi 2B. It is designed as an add-on board that connects to the main GPIO header of the Raspberry Pi. It provides a bit-perfect output meaning that the audio data stream will not be modified in any way. It is in a HAT configuration and therefore with the onboard EEPROM is extremely easy to mount on the Raspberry Pi and can configure itself automatically.
This is the standard version which does not have and output transformer to provide full galvanic isolation between the Raspberry Pi and your DAC on the electrical output. The standard version is usually the best one for most purposes, however there is a transformer version available as well.
- Dedicated S/PDIF interface chip supports up to 192kHz/24bit resolution.
- Optical (Toslink) and electrical outputs.
- Bit-perfect output, audio data stream will not be modified in any way.
- Connects directly to the Raspberry Pi, no additional cables needed.
- No soldering. The Digi+ comes as a pre-fabricated kit. You just plug it onto the Raspberry Pi B+. The board conform to the Raspberry Pi hardware-attached-on-top (HAT) specification. That means it perfectly fits your Raspberry Pi A+, B+ or 2B.
- Directly powered from the Raspberry Pi, no additional power supply required.
- Optional: high-bandwidth output transformer provides full galvanic isolation of the electrical output (not in the standard version).
- Integrated EEPROM for automatic configuration (with write-protection). Note that this feature is still in development by the Raspberry Pi foundation. You will be able to upgrade your HiFiBerry DAC+ when it is officially available. The sound card already works without this feature.
- Comes with all components required to mount it. We include 4 M2.5x12mm spacers to fix the board onto the Raspberry Pi.
Only £29.99 inc VAT.
ORDER NOW
Nano USB Bluetooth Dongle v2.0 for Raspberry Pi @ £3.95 inc VAT
Tested for compatibility with the Raspberry Pi, our nano bluetooth USB Dongle v2.0 is compatible with both newer v2.0 (up to 3.0 Mbps) and the old specification v1.2 Bluethooth devices. This nano bluetooth dongle can be used to get your Raspberry Pi interacting with all your bluetooth devices such as headsets, notebooks, PDAs, handheld PCs, Digital Cameras, Printers and Mobile Phones. This is the most up to date version of the nano dongle currently available – make sure you’re not caught out with older ones which might not work!
Designed with space saving in mind, this Bluetooth Dongle measures 2.2cm x 2 cm.
Features:
- Bluetooth v2.0 and v1.2 Compliant
- Internal Red LED to show that the device is working correctly
- Supporting profiles : Networking, Dial-up, Fax, LAN Access and Headsets
- USB Interface
- Symbol rate : 3 Mbps
- Range : 20m
- Tested for compatibility with the Raspberry Pi
Only £3.95 inc VAT.
ORDER NOW
Miniature Wireless USB Keyboard with Touchpad @ £25.99 inc VAT
This compact little wireless keyboard with built in trackpad is perfect for your Raspberry Pi. Easily the best looking and most functional Mini Wireless Mouse and Keyboard on the market, this is the perfect option for your Raspberry Pi XBMC or slim-line set-up! It’s been tested for full compatibility, and comes equipped with a tiny, low-current nano dongle, so there’s no messy wires to trip over.
The mousepad is sensitive enough to control across large resolutions, but not so sensitive that you need a pin to aim it. It’s also positioned so you won’t accidently brush it when you’re typing. The whole unit fits neaty and comfortably in two hands for typing, and is the same size and shape of a standard TV remote control (it’s actually a little smaller than most), so can effortlessly slide into your sofa setup!
Features:
- Full qwerty keyboard
- Built in touch pad can be switched 90° for ease of use
- Keyboard backlight for ease of use even in dim environments
- Multimedia control keys
- Wireless connection – 2.4GHz DSSS radio transceiver
- Built in rechargeable Lithium Ion battery – recharge via supplied USB (cable supplied)
- Integrated laser pointer
- Auto sleep and wake feature
- Maximum range 30m/100ft
Only £25.99 inc VAT.
ORDER NOW
View the full range here
RPi Display 2.8" TFT Touch Screen for Raspberry Pi Model B+ @ £34.99 inc VAT
Extend your Raspberry Pi Model B+ with a 2.8" full color display (320×240) with touch panel. There is a framebuffer driver available for this display, so you can use it right out of the box.
This screen has a resolution of 320×240, 3 tactile switches on board, a PWM dimmable backlight and even breaks out the 40 pin GPIO header using an FFC cable so is perfect for any application.
Specification:-
- TFT-Display: 2.83", 240×320 (Transmissive)
- Viewing area: 43.2 x 57.6mm
- Touch Controller: TI ADS7846/TSC2046
- Backlight dimmable (PWM)
- Interface: SPI (Touch Controller + Display)
- 3 tactile switches
- GPIOs available via 40 pin FFC/ZIF-Connector
- Power: 5V
- Raspberry Pi Model B+ Pinout
- Fully assembled
Only £34.99 inc VAT.
ORDER NOW
HiFiBerry DAC+ – Phone Jack Version @ £29.99 inc VAT
Improve your sound! HiFiBerry DAC+ – is a high-resolution digital-to-analog converter for the Raspberry Pi Model A+/B+ and 2B. This is a special sound card for the Raspberry Pi, that is optimized for one specific use case: the best audio playback quality.
This is the phone jack version (there is also an RCA version) which will give you the smallest DAC that is available anywhere. The phone jack is mounted on the bottom of the board for minimal height. This version will fit into many existing Raspberry Pi cases. You just have to drill a hole into the case where the jack is located.
This is still a line-output and not designed to drive headphones. For the use with headphones you will need an additional headphone amplifier.
- Dedicated 192kHz/24bit high-quality Burr-Brown DAC for best sound quality.
- Hardware volume control. You can control the output volume using “alsamixer” or any application that - supports ALSA mixer controls.
- Connects directly to the Raspberry Pi, no additional cables needed.
- No soldering required – comes as a pre-fabricated kit. You just plug it onto the Raspberry Pi B+, conform to the Raspberry Pi hardware-attached-on-top (HAT) specification. Mounted in less than a minute.
- Compatible with Raspberry Pi Model A+, B+ and 2B
- Directly powered from the Raspberry Pi, no additional power supply.
- Ultra-low-noise voltage regulator for optimal audio performance.
Available with different output connectors:
RCA or 3.5mm phone jack.
- Integrated EEPROM for automatic configuration (with write-protection). Note that this feature is still in development by the Raspberry Pi foundation. You will be able to upgrade your HiFiBerry DAC+ when it is officially available. The sound card already works without this feature.
- Comes with all components required to mount it. We include 4 M2.5x12mm spacers to fix the board onto the Raspberry Pi.
*Notice about the compatibility with Raspberry Pi Model A and B: This board is only compatible with the new Raspberry Pi Model A+, B+ and 2B. If you have an older Raspberry Pi, please use the HiFiBerry DAC.
Only £29.99 inc VAT.
ORDER NOW
8GB Micro SD – Samsung Pre-Loaded with NOOBS (Official Card & Adapter) @ £7.99 inc VAT
This Official Micro SD Card Bundle for the Raspberry Pi consists of a Samsung Class 6 Micro SD card pre-loaded with the Official Raspberry Pi NOOBS (New Out of Box Software) package, and a beautifully screen printed Micro SD card adaptor with the Raspberry Pi logo! Simply plug this SD card into your Raspberry Pi, and on first boot you will be given a choice of six recommended Raspberry Pi Operating Systems, including:
- Archlinux – A Lightweight and Flexible Linux Distribution
- OpecELEC (Open Embedded Linux Entertainment Center) – XBMC Media Centre OS.
- Pidora – A Fedora Remix optimized for the Raspberry Pi
- RaspBMC – A Linux Distribution Based on Debian that brings XBMC to your Raspberry Pi
- Raspbian – The recommended OS, which contains LXDE, Midori and Development Tools
- RiscOS – Designed in Cambridge, England by Acorn. Released in 1987, it’s a little bit of history!
A note on SD card nomenclature. The card we’re offering here is rated as Class 6 – in some metrics, Class 6 means slow. This is not the case with this card, which has outperformed many Class 10 cards in our tests – classification seems not to correlate well with random read/write performance. Samsung’s unusual focus on random-access performance on their SD memory means that this card performs very fast and very reliably: we think you’ll be pleasantly surprised!
The Samsung 8GB NOOBS Pre-Loaded Micro SD Card & Adaptor Features:
- Superior Random-Access Performance – Perfect for the Raspberry Pi
- Safe from X-rays and magnetic fields
- Reliable shock-proof technology
- Water and dust proof, thanks to EMC coating
- Tested and proven to last up to 24 hours in sea water
- Capacity : 8GB
- Weight : Approx 0.2g
- Operating Voltage : 2.7 ~ 3.6V
- Speed Class 6
Only £7.99 inc VAT.
ORDER NOW
HiFiBerry Amp+ @ £60.00 inc VAT
The HiFiBerry Amp+ is a high-quality, highly efficient Class-D power amplifier for the Raspberry Pi. Mount it onto the Raspberry Pi model A+, B+ or the new Raspberry Pi 2B and you have a stereo audio system. You only have to connect your loudspeakers. It is the ideal building block for multi-room audio installations.
- Class-D amplifier with up to 2x25W output power.
- Capable of driving 4 Ohm speakers.
- Fully controllable from the Raspberry Pi.
- 44.1kHz and 48kHz sample rates.
- Digital-analog conversion included, no need for external DACs or sound cards.
- Fully digital sound path for optimal audio performance.
- Connects directly to the Raspberry Pi, no additional cables needed.
- Integrated voltage regulator for the Raspberry Pi.
- Only one 12-18V external power supply needed for both AMP and the Raspberry Pi, no need for a USB power supply as well. We also stock a suitable 12V PSU and 18V PSU in our store.
- Comes as a pre-fabricated kit, just plug in onto your Raspberry Pi A+, B+ or 2B. The necessary spacers are already included!
Only £60.00 inc VAT.
ORDER NOW
HiFiBerry Case+ for DAC+ (RCA) and Digi+ – Black @ £11.99 inc VAT
A laser-cut case for the Raspberry Pi Model B+/2B and the HiFiBerry DAC+ (RCA version) or Digi+ made from clear acrlyic plastic.
Note that this case is not compatible with the the Raspberry Pi Model A/B and the HiFiBerry DAC or Digi. Use the HiFiBerry case for these boards. The Model A+ will fit inside, but it will not be a particularly sturdy fit.
Only £11.99 inc VAT.
ORDER NOW
HiFiBerry DAC+ – RCA Version @ £29.99 inc VAT
Improve your sound! The HiFiBerry DAC+ is a high-resolution digital-to-analog converter for the Raspberry Pi Model A+/B+ and 2B. This is a special sound card for the Raspberry Pi, that is optimized for one specific use case: the best audio playback quality.
This is the standard version which uses RCA connectors that you know from your normal stereo equipment (there is also a phone jack version). You can use any RCA cable you like. You can even add a phone jack onto the board (you have to solder it by yourself).
Dedicated 192kHz/24bit high-quality Burr-Brown DAC for best sound quality.
Hardware volume control. You can control the output volume using “alsamixer” or any application that supports ALSA mixer controls.
Connects directly to the Raspberry Pi, no additional cables needed.
No soldering required – comes as a pre-fabricated kit. You just plug it onto the Raspberry Pi B+, conform to the Raspberry Pi hardware-attached-on-top (HAT) specification. Mounted in less than a minute.
Compatible with Raspberry Pi Model A+, B+ and 2B
Directly powered from the Raspberry Pi, no additional power supply.
Ultra-low-noise voltage regulator for optimal audio performance.
>Available with different output connectors: RCA or 3.5mm phone jack.
Integrated EEPROM for automatic configuration (with write-protection). Note that this feature is still in development by the Raspberry Pi foundation. You will be able to upgrade your HiFiBerry DAC+ when it is officially available. The sound card already works without this feature.
Comes with all components required to mount it. We include 4 M2.5x12mm spacers to fix the board onto the Raspberry Pi.
Notice about the compatibility with Raspberry Pi Model A and B: This board is only compatible with the new Raspberry Pi Model A+, B+ and 2B. If you have an older Raspberry Pi, please use the HiFiBerry DAC.
Only £29.99 inc VAT.
ORDER NOW
HiFiBerry Digi+ – Standard Version @ £29.99 inc VAT
The HiFiBerry Digi+ is a high-quality S/PDIF output board for the Raspberry Pi model A+/B+ and the new Raspberry Pi 2B. It is designed as an add-on board that connects to the main GPIO header of the Raspberry Pi. It provides a bit-perfect output meaning that the audio data stream will not be modified in any way. It is in a HAT configuration and therefore with the onboard EEPROM is extremely easy to mount on the Raspberry Pi and can configure itself automatically.
This is the standard version which does not have and output transformer to provide full galvanic isolation between the Raspberry Pi and your DAC on the electrical output. The standard version is usually the best one for most purposes, however there is a transformer version available as well.
- Dedicated S/PDIF interface chip supports up to 192kHz/24bit resolution.
- Optical (Toslink) and electrical outputs.
- Bit-perfect output, audio data stream will not be modified in any way.
- Connects directly to the Raspberry Pi, no additional cables needed.
- No soldering. The Digi+ comes as a pre-fabricated kit. You just plug it onto the Raspberry Pi B+. The board conform to the Raspberry Pi hardware-attached-on-top (HAT) specification. That means it perfectly fits your Raspberry Pi A+, B+ or 2B.
- Directly powered from the Raspberry Pi, no additional power supply required.
- Optional: high-bandwidth output transformer provides full galvanic isolation of the electrical output (not in the standard version).
- Integrated EEPROM for automatic configuration (with write-protection). Note that this feature is still in development by the Raspberry Pi foundation. You will be able to upgrade your HiFiBerry DAC+ when it is officially available. The sound card already works without this feature.
- Comes with all components required to mount it. We include 4 M2.5x12mm spacers to fix the board onto the Raspberry Pi.
Only £29.99 inc VAT.
ORDER NOW
Nano USB Bluetooth Dongle v2.0 for Raspberry Pi @ £3.95 inc VAT
Tested for compatibility with the Raspberry Pi, our nano bluetooth USB Dongle v2.0 is compatible with both newer v2.0 (up to 3.0 Mbps) and the old specification v1.2 Bluethooth devices. This nano bluetooth dongle can be used to get your Raspberry Pi interacting with all your bluetooth devices such as headsets, notebooks, PDAs, handheld PCs, Digital Cameras, Printers and Mobile Phones. This is the most up to date version of the nano dongle currently available – make sure you’re not caught out with older ones which might not work!
Designed with space saving in mind, this Bluetooth Dongle measures 2.2cm x 2 cm.
Features:
- Bluetooth v2.0 and v1.2 Compliant
- Internal Red LED to show that the device is working correctly
- Supporting profiles : Networking, Dial-up, Fax, LAN Access and Headsets
- USB Interface
- Symbol rate : 3 Mbps
- Range : 20m
- Tested for compatibility with the Raspberry Pi
Only £3.95 inc VAT.
ORDER NOW
Miniature Wireless USB Keyboard with Touchpad @ £25.99 inc VAT
This compact little wireless keyboard with built in trackpad is perfect for your Raspberry Pi. Easily the best looking and most functional Mini Wireless Mouse and Keyboard on the market, this is the perfect option for your Raspberry Pi XBMC or slim-line set-up! It’s been tested for full compatibility, and comes equipped with a tiny, low-current nano dongle, so there’s no messy wires to trip over.
The mousepad is sensitive enough to control across large resolutions, but not so sensitive that you need a pin to aim it. It’s also positioned so you won’t accidently brush it when you’re typing. The whole unit fits neaty and comfortably in two hands for typing, and is the same size and shape of a standard TV remote control (it’s actually a little smaller than most), so can effortlessly slide into your sofa setup!
Features:
- Full qwerty keyboard
- Built in touch pad can be switched 90° for ease of use
- Keyboard backlight for ease of use even in dim environments
- Multimedia control keys
- Wireless connection – 2.4GHz DSSS radio transceiver
- Built in rechargeable Lithium Ion battery – recharge via supplied USB (cable supplied)
- Integrated laser pointer
- Auto sleep and wake feature
- Maximum range 30m/100ft
Only £25.99 inc VAT.
ORDER NOW