Tommorow's Little Task...

Soldato
Joined
18 Oct 2002
Posts
12,712
Location
Manchester
Having never done any kind of engine work before, I thought I'd try something nice and easy to start with, an oil, filter and spark plug change! Easy peasy!

DSCF0087.jpg


Having stocked up (thought I might as well get a jack and stands, I could struggle, but I'll use them again hopefully..) I found myself a nice easy engine to start on too!


Er..

Maybe not..

DSCF0090.jpg

Engine or washing machine? Not really sure..

DSCF0089.jpg

Spot the spark plugs. Ones under all those hoses and cables somewhere. Right next to the washer bottle. Easy access eh?

At least the oil change will be nice and easy..

DSCF0092.jpg

I think there's an engine under there somewhere :o

Wish me luck!
 
ScoobyDoo69 said:
andi mate, easy jobs !!

sparkplugs, for the passengers side remove the washer bottle (well just move it a bit) and you'll have access, if not remove the battery too.
for the driver's side just remove the air filter ducting - very simple.

oil... well I shouldnt need to explain that one :p

Today i changed all the ignition leads, lambda sensor, got proper gaskets for my decats... what a difference it makes. I had one shoddy ignition lead which meant it ran dodgy, but now it runs great, and WHAT A NOISE !!!

:D

ScoobyDoo69


Cheers for that, was thinking of moving the washer bottle, nice to have it confirmed. Can I leave it full and plumbed in and just move it a bit? Other side doesn't look too tricky. Quite looking forward to it, can't wait to get my hands dirty for once :D

Have you had yours up on stands? Not sure where to stick them, manual says jacking points, but don't fancy mashing the sills..
 
Last edited:
ScoobyDoo69 said:
yeah just leave it plumped in, all you need to do is remove its cable for its electrics... well there's a plug connected anyways, it's green, you'll see it. Once disconnected it moves a good bit.
when is the proper engine work going to start ;)

never put it on stands... dont have any, i use ramps. but the jacking points are easily found, bout 5cm back from the start of the side skirt

Ta. Proper work starts when I earn proper money. Just this service has skinted me till payday on the 15th :o

Used the jacking points before with the standard jack, but don't want to bend the sill or anything. Have seen wishbones mentioned, but want to be sure really.
 
Yeah, sorry, was the mounting point not the wishbone itself.

This was what was said..

Once its jacked up, look behind the front wheels, and the very lower part of whats behind it is the wishbone. It splits and goes to 2 places, one towards the engine, the other rearwards.

Follow it rearwards and see where it mounts, crudly underneath where the accelerator pedal is, but obviously underneath the car.

I use the wishbone points because the chasis is not strong enough for a axle stand to touch without damaging it.

That sound ok to you?
 
Well what a crap day..

Started with the oil, drove round for a few minutes to get the oil warm to make the task easier. Then started the task of jacking it up and getting it on the stands. Pretty scary for the first time, but managed that ok, and access was vastly improved, even with the stands on their lowest setting.

So off came the undertray, and, all prepared with an old oil bottle to catch the oil in, I attacked the drain plug. Which was stuck solid. Was done up rather tight, and with access to just a small socket set, I stuggled for 2 hours, tried allsorts, but it wasn't budging. So dropped it off the stand and ran it down to the garage at the end of the road, where it took the kind old man approx 0.2s with a breaker bar to crack it off. Oh how easy things are with the right tools.

So, back home, I get it back on stands and commence oil drain. Managed to cover myself and the road and everything within a 3 foot radius in oil, but hey, thats part of the fun! Next job, filter. Dead easy, manual states it should be hand tight. Obviously last bloke knew better. No budging. Sigh. No way I'm going to go back to the garage, and anyway, its got no oil in now. So its off to halfords for a filter wrench (I know, I could have shoved a screwdriver through, but with my luck I'd of slipped and gone through the sump or something expensive..). This is turning into an expensive oil change.

So, get back, remove filter and throw it as far as possible, and fit the new (prefilled) one. Stick the new washer on the sump plug and tighten it (but not too tight..). Tada. Now we're starting to do well. So, full of confidence, in goes the new oil. Bit at a time, checking the dipstick, then adding a bit more. Wonderful. Step back, admire handywork. Notice car is still on stands. Slowly realise oil is now all at back of engine, and dipstick is at front. Ah crap.

So off the stands and recheck oil. Oops. Under car, drain plug sloooowly out and drain a bit off. Recheck. Lovely.

So, 5 hours in, and I've changed the oil. I am the master of Mechanics.

Next is plugs. With the wonderous design of the boxer engine, this means dismantling half the bay. Whoopee. Finnally, I can see the leads going into the side of the engine! Surely the next bits easy! I'll just get the spark plug socket and stick it on the ratchet and.. ah.. 1/2" socket, 3/8" ratchet. Wonderful.

And so this is how I left the plugs, deciding that this is a sign I shouldn't be allowed near cars alone again. Stuff whoever is sending these signs though, I'll try and find something that'll fit tommorrow. After a bit of tidying I needed to shift the car. So, fingers crossed, I climb into the seat and turn the key. Fully expecting to hear the sound of grinding metal or a piston to come through the bulkhead and hit me in the knackers, I was plesently surprised when she started perfectly, and purred rather nicely. Roars quite nice too with half the induction system missing too. :D

So only a partial, and rather drawn out success (aren't I the optimist..). But I know more than I did this morning, which was the point of the exercise I suppose.

DSCF0097.jpg

Lowering is so last week, the new thing is the rallyslag look

DSCF0099.jpg

Note mum's best tupperware. She'll go mad if she finds out..

DSCF0102.JPG

Your supposed to get the oil in the container...

DSCF0101.JPG

Note to self: On hot days, place board under jack..
 
DSCF0103.jpg

Look at her, looking all innocent. Bitch.

DSCF0106.JPG

Like assembling flatpack, you always end up with a few bits left over and no idea where they go..
 
-westy- said:
Its definately worth investing in a decent size socket set if you plan on servicing /working on your car yourself :)

Very true. Decent socket set and a fairly sized breaker bar are on the shopping list, I really underestimated how crap our collection of tools is. I had to go to work to borrow a flipping hammer :rolleyes:

Turning out expensive but hopefully I'll use most of the stuff I've bought again, jack, axle stands, filter wrench, and now something to do the plugs probably. Adds up fast.
 
GT3 said:
I had that fun with the sump plug the first time I changed my oil. But I couldn't be doing with taking it to a garage, or heaven forbid buy any tools. So I took the hacksaw to my mums garden rake and made a breaker bar :p

:D

Bet your mum loved you :D
 
Did the plugs today. Simple enough once I had a decent sized Spark Plug Wrench to do it with, and I moved all the bits out of the way. Right hand plugs were a bit of a bitch, but nothing too bad. Now runs beautifully.

Took the old oil to the tip and went to halfords earlier before I'd put it back together, and my god it sounds ace without the resonator boxes on the intake :D Need an induction kit I think :D

Dad's agreed to go halves on a decent socket set too :cool:
 
Back
Top Bottom