tools need to assemble PC

wangchen1990

wangchen1990

wangchen1990

Associate
Joined
6 Apr 2011
Posts
132
Location
Newcastle-upon-Tyne
Hi
I was going to assemble a custom gaming rig. But I'm lack of tools like screw drivers.
It is so kind of u if you can share some information of useful tools to me to assemble a PC.
Also I'm looking forward to get some help to remove the anti-glare coat of my DELL U2711, wonder somebody can give me a hand. I'm really afraid to do it myself.
 
Hmm I think all you really need is a Phillips screwdriver. Maybe a big flat head one can help as well with certain things (case screws) but not required.

Your best (metaphorical) tools are time and space :)

What you building?
 
I have a 'Draper 31 piece precision screwdriver set' from the rainforest store, it's great for working with computers and general things around the house. It was about £5.
 
If you're installing a DHT cpu cooler, then I've found an old credit card/store card to be indispensable when applying the heat sink paste. Other than that though, you're pretty much covered if you've got a Philips head and somewhere clean and dust free to work.

Personally, I'd also get an anti-static wrist band. A lot of people say they're not worth it but the way I see it is why scrimp on something that cost less than a fiver (some are even less than a pound) when it could save you from bricking an expensive piece of hardware?
 
Last edited:
Thank you for ur advice . Here is what i plan 2 do .
1. my current system which has already been built by my friends.;
i5 2500k , Asrock Fal1ty P67 mob, 4*2GB G.skill memory .
Gainwind GTX 580. 1 60GB SSD, 2 30GB SSD and 1 500GB HDD.
Cpu cooler is Akasa AK-CCX-4002HP Venom CPU Cooler (Socket LGA775/LGA1155/LGA1156/LGA1366/AM2/AM3)
***I need to switch the P67 mob which is faulty now to Z77 mob and put everything back ****
2. I wish to remove the anti-glare coat of my DELL u2711. I dont think i will do it unless got somebody's help.
3. I have ordered a new Samsung S23A700D 23" 120Hz 3D Widescreen Gaming Monitor.
i wish to use it as my 2nd monitor . which wont be used as eye infinitely for games. But i wonder maybe it is possible to use 2 monitors when i was surfing website and working and just 1 monitor when gaming.

Thank you again for all your help. I'm not familiar with mob at all. SO a lot of reading needs to be done
 
yes that is possible. I used to have a small second screen when I was doing my dissertation.

all you will need is a phillips screwdriver and potentially a flathead screw driver otherwise you should be good to go.

I use compressed gas and a small paint brush to remove dust. I use a shop in the rain forest for it ;)


if you wish to remove the glare and seek assistance I would suggest posting a new thread in the monitors subforum. I believe this would be the most likely place of help for you. Here:

http://forums.overclockers.co.uk/forumdisplay.php?f=85
 
Last edited:
skylineboy said:
yes that is possible. I used to have a small second screen when I was doing my dissertation.

all you will need is a phillips screwdriver and potentially a flathead screw driver otherwise you should be good to go.

if you wish to remove the glare and seek assistance I would suggest posting a new thread in the monitors subforum. I believe this would be the most likely place of help for you. Here:

http://forums.overclockers.co.uk/forumdisplay.php?f=85
Click to expand...

that flathead screw driver is used for case screws right ? I have a NZXT Phantom Enthusiast USB3.0 Full Tower Case.
So i suppose i wont need that driver for this case?
I have post a thread earlier as i said, it is not urgent .I have watched the youtube video. I'm afraid to do it myself without professional help. The warranty is not covered for this kind of damadge
 
Last edited:
Can of compressed air from any motor factors.....but I find a good 1-2" brush works perfect if you take your time.
 
I would buy a few cross head screw drivers.

Firstly make sure they're light, get some different lengths too, I have had some hard to reach screws when the coolers attached for instance so a driver with a long shaft was very usefull.

Also get your self some small cable ties, some self adhesive bases and some light duty cable snips, makes cable management a breeze.

Tip: Mangnetize your screw drivers, put them on a radiator or magnet, saves dropping screws.
 
Magentised positive screwdriver, small and large flathead screwdrivers, pair of pliers and a pair of wire cutters for those pesky cable ties.
 
Garyj881 said:
Tip: Mangnetize your screw drivers, put them on a radiator or magnet, saves dropping screws.
Click to expand...

Are you saying to put them on a radiator to magnitise them? How does that work? I'm interested lol ... if that is what you mean by that

darael said:
Magentised positive screwdriver, small and large flathead screwdrivers, pair of pliers and a pair of wire cutters for those pesky cable ties.
Click to expand...

Also, when I built my PC, I intentionally used screwdrivers that were NOT magnetised as I thought that would be bad for the PC and parts to use magnetised ones.

Assuming it's ok to use magnetised screwdrivers then?
 
Do not buy cheap tools, ie - screw drivers as they are made from cheap metal and the tip can wear. So slip on the screw head thus damaging the head which can be a pain in the butt to remove.
 
A top quality Phillips head screw driver.

If doing a rebuild or modification, I like to have a small paintbrush and compressed air on standby.
 
Garyj881 said:
I would buy a few cross head screw drivers.

Firstly make sure they're light, get some different lengths too, I have had some hard to reach screws when the coolers attached for instance so a driver with a long shaft was very usefull.

Also get your self some small cable ties, some self adhesive bases and some light duty cable snips, makes cable management a breeze.

Tip: Mangnetize your screw drivers, put them on a radiator or magnet, saves dropping screws.
Click to expand...

So brilliant !! thanks
 
You must log in or register to reply here.
Back
Top Bottom