UK IC Diamond Rep

[frostdragon]

Hello folks;

I am your UK-Based rep for Innovation Cooling's IC-Diamond and am pleased to liaise with you all.

I see many new and old faces (or rather names) here and I am here to help you with any questions you may have. Ideas on application and use will also be very much welcomed

Anyway we will be starting a thread under the cooling-sections of the forums and we are only too eager to help with issues and feedback

Cheers

Frost Dragon
Innovation Cooling IC-DIAMOND UK REP

 

[fiveub]

Welcome to the forum!

 

[Hyburnate]

Welcome

 

[SeraphX]

Welcome to the forums

 

[jamesfreddie]

You may want to have a look at your website as one of the links on there is very close to promoting illegal activity

 

[frostdragon]

You may want to have a look at your website as one of the links on there is very close to promoting illegal activity

Sorry there can you supply further information as I am unsure to what you are referring to.

 

[Doraku]

Sorry there can you supply further information as I am unsure to what you are referring to.

I think he might be making a joke.

"ILLEGEAR"..

 

[jamesfreddie]

Sorry there can you supply further information as I am unsure to what you are referring to.

Setup your trust and I can send you a link, can't really mention it on the forums.

 

[fiveub]

Send to me please and I shall pass on in the meantime. Thanks.

 

[jh30uk]

Where did the last Rep go that gave out free samples here years back?

Any change to your product as it is a nightmare to work with.

 

[frostdragon]

Where did the last Rep go that gave out free samples here years back?

Any change to your product as it is a nightmare to work with.

Sorry you feel that way. THe TIm is still the same, however we have developed a better way of applying it.

 

[jh30uk]

Cool so its not just a blob and use sink to press it outward as you tighten?

I know you do not spread it but its hard to get it out the tube and not stick to nozzle, I tried putting it in a cup of boiling water and it may have helped a little.

 

[jamesfreddie]

Send to me please and I shall pass on in the meantime. Thanks.

Sent

 

[rjk]

Hi frostdragon

Welcome to the forum, great to have you on board.

I am the TIM buyer for Overclockers UK

if you need to speak to me regarding anything, my email is [email protected]

Rich

 

[frostdragon]

Cool so its not just a blob and use sink to press it outward as you tighten?

I know you do not spread it but its hard to get it out the tube and not stick to nozzle, I tried putting it in a cup of boiling water and it may have helped a little.

Hey there:

Best way I have found and what how i apply it is as thus:

BTW I LOVE these intelligent questions, helps us to devise easier ways to apply the TIM.

Best way to warm up the TIM and the easiest, is to simply but the tube under your armpit for 10 mins. Well when I say armpit, i mean BARE FLESH armpit (come on i know you want to) this heats up the IC-Diamond TIM nicely.

The IC-Diamond TIM should come out nicely now

On INTEL CPU'S UPT O and Including 1366/1150 and 1155 (by IHS size) try putting a 5.5mm sized blob in the centre and letting the heatsink /water block spread it out........ Do not be tempted to look to see how far it has spread as this will introduce oxygen bubbles into the layer.

INTEL CPU 2011 PIN Best way is to Put a blob in the centre 5.5mm in size and then thirds towards EACH corner of the CPU IHS another blob around 2.5mm in size. Making a 5 point pattern..........do not join the dots with TIM as this will be a waste of product as those five points are enough to spread the TIM out along a 2011 pin IHS.

Will post this in this ICD thread, oh will also do photos and a recommended GPU IHS application also.