what cpu volts you using for e6300?

serenity888 · 13 Jan 2007 at 18:07

My e6300 is sitting at 1.325v (clocked at 3.01ghz) with temps of 40C idle and 55 under load. I'm wondering voltage other people are using as i may try lowering it to decrease the temps a bit more.

Rofflay · 13 Jan 2007 at 18:25

im using 1.25v at 3.08 on my e6300.

btw 55c load is fine tbh if its with both cores loaded i get 62c sometimes.

GazD · 13 Jan 2007 at 18:27

1.3v @ 3.29Ghz, around 50c-53c fully loaded.

Rob43 · 13 Jan 2007 at 18:45

[email protected] on mine

Never above 45C

furnace · 13 Jan 2007 at 19:15

Rob43 said:
[email protected] on mine Never above 45C

What cooler do you use?

Stock clock speeds on an E6300 here, 1.25v, temps are ~40'c idle, ~53c full load.

My next steps:
Do something to the top of my case to let hot air out
lap CPU with finer grain paper than the 1500 I already used
lap ACF7
see what temps are, if not so good I'll get a better cooler
THEN I might overclock.

Not really a good idea to overclock at my temps, is it..?

Rob43 · 13 Jan 2007 at 19:26

furnace said:
What cooler do you use?

All under water mate

micky1up · 14 Jan 2007 at 03:03

im using a zalman 7700cu fan and the voltage is 1.265 and my idle is 40 and load around 53 i may try lapping aswell

jongeeone · 14 Jan 2007 at 13:01

AFC7 @ 1.3v / 45 idle / 55 load

beast · 14 Jan 2007 at 13:26

Rob43 said:
All under waterQUOTE]

Surely that's dangerous

jongeeone · 14 Jan 2007 at 14:32

lol

i belived this has been done?? or some one was pulling my leg

Soak all your components in oil expect the psu and submerge it in water (except the psu) and then submerge it in water....

any volenteers?

Cuchulain · 14 Jan 2007 at 14:34

1.45V for me, any lower and it won't prime.

Sniper123 · 14 Jan 2007 at 15:03

1.35 for 465*7 (3.25GHz)
Idle 37C
Load 47C

Thats with TT120 at max speed, I would normally set my TT120 to 1500rpm so I don't get a headache

OC_A64 · 14 Jan 2007 at 15:10

1.26v for 3.1ghz. (stock air)
1.34v for 3.4ghz (stock air)
1.4v for 3.7ghz. (water)
^^ Are orthos stable at these speeds.

and ~ 1.5v for 4.2ghz (only pi1m stable, however thats a ram or mobo limit not CPU) - phase cooled.

Sniper123 · 14 Jan 2007 at 15:28

OC_A64 said:
1.26v for 3.1ghz. (stock air)
1.34v for 3.4ghz (stock air)
1.4v for 3.7ghz. (water)
^^ Are orthos stable at these speeds.

and ~ 1.5v for 4.2ghz (only pi1m stable, however thats a ram or mobo limit not CPU) - phase cooled.

Wish my 6300 was that good

Above 480*7 only 1 of my cores is stable no matter what the volts. :mad:

Faffer · 15 Jan 2007 at 12:03

1.3375V @ 3.29GHz
around 37C idle and 47C under load.
using Tuniq Tower with Arctic Silver paste, unlapped.
CPU fan at full speed.

mxjames1 · 15 Jan 2007 at 12:09

E6300 @3.325
42 deg C under heavy load super pi and prime 95 both cores
31 deg C now using forum

cpu core: 1.46250v
tuniq tower 12mm surounded by 2 1200 mm case fans