• Notice regarding image hosts and attachments. See here.

Road Cycling Essentials

Status
Not open for further replies.
Well, we've reached the end of my technical knowledge :p
Did you read the parktools guide? That will explain things better than i can.
 
Just been out for a tinker in the car park. I loosened the cable 1 turn and it started jumping to the highest gear even if I hadn't selected it. So I tightened it again 1/2 turn and it was hunting for the gear. Went 1/4 turn either side of that and I still can't get it right, so back to the drawing board this weekend starting with:

Did you read the parktools guide? That will explain things better than i can.

Thanks all.
 
The cable shouldn't really be loose at all, sometimes front mech ones need to have slack in them to shift properly though.

Undo the cable clamp with the 5mm allen key. Whilst turning the cranks check the mech is sitting in the hardest gear...if it's not then adjust the H screw out a sqaurter turn a time until it drops down. Once you're sure that's working push the mech by hand up to the easiest gear to check it doesn't go into the spokes. Check by eye to see the mech lining up below the 1st cog from the rear of the bike. Check the bolt holding the mech on is tight too ;)

Wind the barrel adjuster in fully and then take it out a full turn or two. Pull the cable through hand tight. Make sure your outer cables are all seated in their stops properly then clamp it down with the 5mm allen key.

Shift up one gear on your shifter and pedal, if it struggled to jump up to the next gear unscrew the barrell adjuster anti-clockwise a qaurter turn at a time until you get it to jump up. Go up then gear and then check it drops down from easy to hard gears. If it hesitates to drop down wind the adjuster back in clockwise until it does. If it then struggles to go up the gears again your cable might be a bit gritty. On older shifting up you need to persuade it to jump up a cog by pushing the lever a little further than normal. Not ideal but you always want the gears to drop down on their own as you can always tweak it on the way up.

wow wall of text much...my bad.
 
Did my first ever 50 today :) Was happy to do it in the time i did, eventhough it was all flat. Just need to start getting up those hills and get a proper 50 in!

Not sure what happened to my garmin, it tried to change my route a couple of times so didnt quite do the route i planned. And the timing and average speed seems to have got confused! Also had to go back on myself as a road was closed :(

Doing the isle of wight randomee in may, so just a few more climbs in that :p

http://connect.garmin.com/activity/150231130
 
The tool makes it so easy. We had an F3 come in with BB30 issues and thankfully it was a mate of my boss.

Hammer and screwdriver saw the old ones out which were rough as **** after a week. Some sort of washer bodge + press to fit the new ceramic sram ones. I was glad when the tool became available again. Have fun and remember the wavy washer.

Finally managed to get the bike done today though I haven't been able to test ride it properly yet. The BB30 tool was useful but I was surprised how hard I had to hammer the tool to get the bearings out. All nicely coppered up now. Headset press with the bushings make fitting them flush very simple. Glad I waited for the BB30 kit.

Funny reading this back as when I put the non-driveside crank back on I looked up at the bench and the wavy washer was staring at me!! :D
 
Last edited:
Did my first ever 50 today :) Was happy to do it in the time i did, eventhough it was all flat. Just need to start getting up those hills and get a proper 50 in!

Not sure what happened to my garmin, it tried to change my route a couple of times so didnt quite do the route i planned. And the timing and average speed seems to have got confused! Also had to go back on myself as a road was closed :(

Doing the isle of wight randomee in may, so just a few more climbs in that :p

http://connect.garmin.com/activity/150231130

Aah Chichester. I knew it well! Is Roussillon Barracks still there?
 
Not sure what happened to my garmin, it tried to change my route a couple of times so didnt quite do the route i planned. And the timing and average speed seems to have got confused! Also had to go back on myself as a road was closed :(
In the routing options on your garmin turn off auto-recalculate. Otherwise when you load a saved ride it recalculates the route between all the via points, messing up your plans.

2nd century of the year for me tomorrow, should be a nice day for it.
 
Not at all, very informative. Going to tackle it properly tomorrow and will read through this as I go. Thanks!

WP_000654.jpg


That is where the part number is located usually.
 
Tomorrow is supposed to be ok. Sorry folks, but I can't make it tomorrow. Doing a load of work on the house and I've fallen behind schedule. A day off means I might not be finished by the time the carpets and furniture turn up on Friday morning.

Sorry chaps.
 
Wasn't my bike just some random old shifters on bars left in the bin shed.

Should be able to see if without ruining the tape.

Yep, checked and ordered via Madison for £5.99 delivered to my door. Nice chap called Ross at Bromsgrove's Speed Cycles said he'd post it for me at no extra charge. Many thanks.

Washed my bike today so thought I'd take a photo. Hope I haven't broken any 'rules'!

- Not against white background
- Crank arm not aligned with chain stay or seat tube
- Dust caps present
- Masses of spacers below stem
- Chain should be on smallest sprocket

Sorry :p. Nice photo though and a great looking bike.
 
Last edited:
Status
Not open for further replies.
Back
Top Bottom