Photos of a H80 in a Corsair 600T

eg8076 · 27 Jul 2011 at 23:49

Does any one have any photos of a H80 installed in a 600T. I was thinking of getting a H80 to go with my shiny new 600T and would like to see an example.

Rainagul · 28 Jul 2011 at 15:49

Got a H70 in mine, looks roughly the same dimensions as the H80 if thats what your looking for. Need a picture still?

kallisto316 · 29 Jul 2011 at 13:05

Might be a bit tight, here is the H60 in mine...which is thinner than the H80. It will fit fine, but just will look quite full if you know what i mean.

KiiYzOo · 29 Jul 2011 at 13:07

you could always fit one fan to the outside?

kallisto316 · 29 Jul 2011 at 13:13

KiiYzOo said:
you could always fit one fan to the outside?

That's true, could be a good option for you.

Freddie1980 · 29 Jul 2011 at 13:32

Did you lose your Crossfire/SLI bridge? That's a smart looking case BTW.

KiiYzOo · 29 Jul 2011 at 13:38

you don't need one to run sli, but it will perform better with one

Broken Hope · 29 Jul 2011 at 13:39

All of Corsair's coolers will fit any of their cases, it isn't an issue at all.

kallisto316 · 29 Jul 2011 at 13:47

Freddie1980 said:
Did you lose your Crossfire/SLI bridge? That's a smart looking case BTW.

It's being sprayed black

eg8076 · 2 Aug 2011 at 22:14

Thanks for all the replys, the photo is great kallisto316, that a really tidy case you have. I hope mine ends up looking something like that when its done.
I might end up getting a H60, as i missed the deal for the H80 i was after.

ray168 · 3 Aug 2011 at 11:20

very nice setup looks amazing.

Mollari · 3 Aug 2011 at 11:54

kallisto316 said:

Really delicious looking- nice!

Apem · 3 Aug 2011 at 15:19

Anyone know on the 600 and 650 cases is the rear exhaust fan grill flat or raised slightly?

bazburn · 3 Aug 2011 at 15:34

I just helped a mate put an H80 in a 600T last night! Fits in fine. One piece of advice i would have would be to plug the mobo power in before you install the cooler.

Purgatory · 3 Aug 2011 at 15:45

Nice job

Looks great. Braid the fan cables for the cooler or get some black heat shrink

will make it look nicer.

Phil3 · 3 Aug 2011 at 22:48

kallisto316 I noticed that you have push pull on your H60, what fans are you using and how do you rate them compared to stock?

Apem · 4 Aug 2011 at 16:36

Apem said:
Anyone know on the 600 and 650 cases is the rear exhaust fan grill flat or raised slightly?

anyone know please?

Broken Hope · 4 Aug 2011 at 17:23

Apem said:
anyone know please?

Slightly raised on the back of the case.

mrk · 4 Aug 2011 at 17:28

Probably 1mm or so, it's so flush it might as well be flat though.

kallisto316 · 4 Aug 2011 at 18:23

Phil3 said:
kallisto316 I noticed that you have push pull on your H60, what fans are you using and how do you rate them compared to stock?

I'm using Gentle Typhoon AP-15's.

The stock fan with the H60 is excellent actually, but you can hear it when you turn it up near maximum. The AP-15's will run much faster at a quieter volume, they also have a better air pressure rating, so they can force more air through the vanes of the radiator. To be honest, I didn't really have to swap the fans but just fancied doing it. Also the build quality and bearings are superb, if you power up the AP-15 and then cut power, it takes ages to spin down...the bearings are that good.

But to reiterate, the fan with the H60 does the job very well, 2 AP-15 are waaay better...if you want to pay the money, but the difference is only a couple of degrees to be fair.