Aspire x1930 Upgrade possibilities

StokieBen

StokieBen

StokieBen

Associate
Joined
12 Apr 2013
Posts
47
Location
Talke Pitts
Couple years ago I brought my x1930 Desktop for the purpose of general internet browsing but recently been getting hooked on Pc gaming, Noticing my system is pretty much terrible for casual gaming I'm looking for some advice on upgrading my Pc. http://www.manualslib.com/manual/232905/Acer-Aspire-X1930.html?page=9

I believe that the SFF chassis it came with could only run low profile cards and with the 220w Psu I wouldn't be able to even run the best low profile cards. I want to stick with the current motherboard which I believe is an MicroATX, but i'm new to building and adding components to computers so I was looking for help.

I believe it's possible to put a MicroATX Motherboard into a Midi case so if anyone could recommend a low priced Midi that fits these needs, I'd also like to get a better PSU but I'm completely inexperienced in where to start with the PSU and how do I know if it will fit my board physically (size and pins). Aswell as a single slot PCI-E graphics card that is around the £100 -175 mark which if my machine allows me to get a more powerful and larger case I'd like to have.
 
It looks to be smaller than microATX. It's probably FlexATX, but you'd need to check with a ruler to be sure. The I/O plate and mounting points look to be in standard locations so you'd probably be okay transplanting it.

What are the rest of the specs. (CPU, memory, etc.)?
 
Here are my suggestions to kick start things regarding GPU/PSU. As bremen said, can you also post the rest of the spec, to see what is salvageable?

7850 2GB, it's on the weekly offer also :)

http://www.overclockers.co.uk/showproduct.php?prodid=GX-289-AS

Assuming you'll be using a fairly low powered system, this corsair module 500w should be fine for your needs. But, ideally need an idea of the full spec first.

http://www.overclockers.co.uk/showproduct.php?prodid=CA-116-CS&groupid=701&catid=123&subcat=1084
 
All micro atx mounting points are present with my motherboard thanks for the help. Also how do I know if a powersupply will work with my otherboard such as what Bromhead linked?

Looking up though might be able to use my pc after some upgrades for some games finally :)
 
The main 24 pin power connector shouldn't cause you any issues.

The other power connector is a 4 pin rather than the more usual 8 pin. This wouldn't usually be a problem as the unused pins can just overhang the socket. On your board there appear to be components on both sides of the socket that would stop an 8 pin connector fitting.

You'll need to check that the PSU either has a dedicated 4 pin connector, or has an 8 pin connector that splits in half. If not you can get extension cables that'll fix the problem.
 
That 4 pin connector is more usually an 8 pin connector.

You need to check that the PSU you choose can connect to it. From the available pictures there appear to be clearance issues that would stop an 8 pin connector working unless it's designed to split into two 4 pin connectors. They often do, but there's no guarantee.

There may actually be enough clearance around the socket, difficult to say without seeing it in the flesh.

In the worst case you'd just need to end up using an adapter cable.
 
Thanks for your advice :) So I should be fine and if it comes to the worst I can just get an adapter cable and will sort the problem and let me use the 500wpsu :)
 
Sorry to re post again but after checking the booklet you linked bremen it appears I have only 6 mounting holes of the total of 9 Possible, this makes my mobo at FlexATX should I see if I can purchase a whole new motherboard instead or will this be able to mount to a midi case that you recommend ? Am I totally screwed and should try and salvage my Hardrive and buy a Normal ATX Mobo?
 
This missing holes shouldn't be a problem if the rest of them are in the correct positions. I'm 99% sure that you'd be fine with any case that claims to be suitable for a microATX motherboard.

If you replace the motherboard you may end-up needing a new copy of Windows. An OEM version of Windows (which is what you'll be running) is tied to the motherboard. It's quite possible that you'd be able to get around that restriction, but a full reinstall is likely to be necessary. Did you get full installation media with the system? I'd guess not. You probably just had the option of creating your own set of recovery disks using blank DVD media (which hopefully you did).

Your plan to rehouse the existing hardware in a full-size case sort of makes sense. Once you get into replacing motherboards you'd probably be better off starting from scratch.
 
You must log in or register to reply here.
Back
Top Bottom