Deleted User 298457
Deleted User 298457
That's not a bird that's an OpenReach engineer
Edit: I see it now; it is just a small ****. Had to zoom in loads
Last edited by a moderator:
Images of items I have purchased (except trainers [no feet pics])
- Thread starter Zefan
- Start date
Edit: I see it now; it is just a small ****. Had to zoom in loads
Soldato
- Joined
- 2 May 2011
- Posts
- 12,140
- Location
- Woking
Soldato
- Joined
- 23 Feb 2009
- Posts
- 4,988
- Location
- South Wirral
They escaped whilst the guards were distracted. Have you people not seen "Chicken Run" 
Have to be covered, i.e. physically segregated from wild birds. Unless you think the rules dont apply to you.... He was called out for it by someone else last year and made some excuse about cleaning them out.
Caporegime
- Joined
- 1 Dec 2010
- Posts
- 53,737
- Location
- Welling, London
That whole enclosure looks like a KFC for wild animals.
Foxes can surely get in there too easily as well
Foxes can surely get in there too easily as well
Lol at some people in here
Even the covered section birds can get in through the mesh
No Rob, the mesh is buried into the ground to deter foxes and the birds are in their catagory 4 bio hazzard safehouse on an evening with 8 point multi fixing hermatically sealed door
All is good
Even the covered section birds can get in through the mesh
No Rob, the mesh is buried into the ground to deter foxes and the birds are in their catagory 4 bio hazzard safehouse on an evening with 8 point multi fixing hermatically sealed door
All is good
Last edited:
That's what KFC stand for right? Keeps ******* Chickens, either that or Keeping Famine Christian
.Think i recall seeing some posts in here about cheap Ali Express special Torque Wrench/Digital Verniers, however can't seem to find them.
Anyone have any recommendations or should i just be looking at Amazon?
(Note ultra accurate verniers aren't necessary)
Anyone have any recommendations or should i just be looking at Amazon?
(Note ultra accurate verniers aren't necessary)
Deleted User 298457
Deleted User 298457
+/- 3 inches can only work in your favour?
You suck at search, discussion about here I think there was a suggestion for a certain brand somewhere IIRC: https://forums.overclockers.co.uk/t...chased-except-trainers.18737970/post-36127574
I might order some myself.
Caporegime
- Joined
- 20 Oct 2002
- Posts
- 75,922
- Location
- Wish i was in a Ramen Shop Counter
This is the point i hold my hands up and admit i didn't actually search and figured someone would do it for me
Torque Wrench wise looks like Amazon is actually cheaper!
Cunningham's Law!
+/- 3 inches can only work in your favour?
My wife has always been told that <----------> = 10 inches. She's rubbish at measurements because of it!
This is the point i hold my hands up and admit i didn't actually search and figured someone would do it for me
Torque Wrench wise looks like Amazon is actually cheaper!
Sod
I have one of these: https://www.machinemart.co.uk/p/cht141-1-2in-drive-torque-wrench/ or at least an older version. Seems to do the job but has seen limited use. Just make sure you set back to zero when finished (also make not of the size of driver type you need, 1/2" might be limiting for what you want, more for wheel nuts and similar).
Sod
I have one of these: https://www.machinemart.co.uk/p/cht141-1-2in-drive-torque-wrench/ or at least an older version. Seems to do the job but has seen limited use. Just make sure you set back to zero when finished (also make not of the size of driver type you need, 1/2" might be limiting for what you want, more for wheel nuts and similar).
Cheers, looks too hefty for my needs. It's for bike building so need one at the lower end. I think that one will demolish a carbon frame!
They do 1/4" drive version - check the torque range in the specs for what you need.
Deleted User 298457
Deleted User 298457
Looks bang on! They've done a great job with the chimney.
Thanks mate
yes, very pleased with it !