memory timings advice

8 Pack said:
No you dont its your chip. ARe temps still under control??? Just use the system then.
Click to expand...

with current settings 1.415v, max temp in 10 runs of IBT(on max) 69c with fans on 40%, so still very quiet :D

just had an hour on BF3 using OC'ed 7970 and max cpu temp is 60c, with an ambient of 21c


This is whilst running catzilla
t_zps22974dda.jpg
 
Last edited:
hows my RAM looking??? so far so good, on its max frequency with those timings, just get error code 50 if i go higher.

rt01_zps44a5526e.jpg
 
Last edited:
the above was not consistant, needed more volts for the ram to remain stable and was already too much.

will ram waterblocks help??

now running ram at 2440MHz with a bus of 101.7 with same timings
 
Last edited:
tried a few of the settings you have suggested, so far so good, any more bud i can try. These settings are stable with OCCT with large data set, IBT on max and cine bench. once i have my final settings then hoping to dial back some voltages.
currently on
vcore 1.4
dram 1.665
pll 1.55
SA 0.985
IO 1.23

also too note, my latency in Aida64 is 32.7ns

final_zps3e267240.jpg
 
Last edited:
Have dropped tREF to its next lowest setting which was 8319, which is also stable, and has improved scores, will try your above suggestions, thx bud :)

*edit* ahhh, maybe not, can run IBT on max but then randomly locks up on desktop, right gone back to 9360 and will try the above.
 
Last edited:
Winston said:
You tried 45 multi using 103bclk?
Click to expand...

yep, can get the ram to run at about 2650MHz but not with tight timings, so below is a screenshot of nice timings and just above stock freq. benchmarks are better for me like this. can push more but this is for 24/7

@ 8Pack tried last recommendations and past OCCT once but PC froze so went back to 148, but upped the BclK a touch, happy with the results ;)
just one thing dram volts, whats the max for 24/7????


final_zps747d979d.jpg
 
Memtweakit does not work with my board, saved my above profile then loaded xmp, latency is up, read, write and copy are down quite a bit but superpi is quicker????
 
My volts in bios for dram are at 1.6650, but underneath that figure its showing 1.69, this board does like to pump it up. Something i dont like personally.
So 8Pack do you think thats my lot??

For certain frequencys and timings is there a rule of thumb regarding voltages.

I.e 2400MHz, 1.25v IO, dram 1.65v??
 
Yeah ok, thought so. Happy now with timings and speed all round, just need to work on those voltages. Even though currently it passes everything there is the odd glitch now and then, but our heating comes on at about 3pm, where ambient rises about 7c for when the mrs gets home! These little blips occur after about 5.30 when the house has warmed up.

Looking at the current weather, looks like i may be having a few more days off so can test further. ;)
Have you had time to have a play with the mpower yet?
Oh and when you suggest settings/timings is there a formula or is it just experience? And thx again for your help.
 
Unfortunately i have to tile our en-suite today, so wont get on pc till later, have a play winston and post here how you get on.
What i want to know is which is better
Higher freq.slacker timings v's lower freq. tight timings
 
^ yep will do, just taking quick break

Just tried everything on auto, will boot at 2600 but not 2666 get debug code 55 which i believe means my ram is not capable at that freq.
 
Hi mate, tried your earlier settings, not much diff. TBH, worked a bit on 2630MHz got them tighter, but didn't have long to test. At that speed, read, copy and write were nearly the same as my tunned 2.4 but latency was lower. How you getting on??
 
You must log in or register to reply here.
Back
Top Bottom