• Notice regarding image hosts and attachments. See here.

Only 4GB RAM showing

Have you made sure the motherboard actually does support the ram your using as some motherboard act funny if you fill all the slots.
 
Yes, my computer says "64-bit Operating System" and SP1 and 2 are both installed along with loads of updates. I dont think this is a problem with windows though because the BIOS is showing 4GB too
 
Interesting. Try setting the memory voltage to 1.6 and raising the northbridge voltage to 0.1v above wherever it is now.

If that doesn't work, remove the sticks one at a time until it detects all the RAM and post back.
 
I haven't tried flashing the BIOS. That sounds dangerous.

Which voltages should i change? In BIOS I've got:-

CPU Voltage
CPU PLL Voltage
QPI/DRAM Core Voltage
IOH Voltage
IOH PCIE Voltage
ICH Voltage
ICH PCIE Voltage
DRAM Bus Voltage
DRAM Data REF Voltage on CHA
DRAM CTRL REF Voltage on CHA
DRAM Data REF Voltage on CHB
DRAM CTRL REF Voltage on CHB
DRAM Data REF Voltage on CHC
DRAM CTRL REF Voltage on CHC
 
Shouldn't need to **** about with voltages. For 12GB you'll have 6 sticks of RAM, try just two lots of 3 at a time and make sure you get 6GB with each lot before you do anything else.
 
Ok, Changing the voltages didnt fix it so i started putting the ram in, in different combinations. Seems that the slot furthest from the CPU must be filled first. When all but the one closest to the CPU are filled it shows up as 10GB. When i insert the last stick it drops back to 4GB
 
I just tried 3 at a time. With 3 sticks filling all of the blue sockets it shows 6GB. With the same 3 sticks filling the black sockets nothing happens. BIOS never loads.

It seems that it will only work when the blue slot furthest from the CPU is filled. Various other combinations do work but with random results. Filling them in order starting with that socket gets the results you would expect until the last one goes in and it jumps back to 4GB
 
I had a similar problem with an Asus board. I fixed it by setting the memory speed manually instead of leaving it on auto. Try setting the DRAM clock to 1333Mhz.
 
According to the ram itself, its actually 1600MHz even though the overclockers website says 1333MHz. I believe the CPU limits it to only 1333MHz though. Is 1333 correct or should it be 1600 and could this have anything to do with the problem? I was told it would just run at 1333MHz without any problems
 
Ok, so you've at least confirmed that one set of 3 sticks gives you 6GB in the blue slots - have you tried the other set of 3 sticks to make sure they also report 6GB?

If they do (ie. once you've confirmed each stick of your RAM is working), and you're still getting the odd issue with the last slot causing the total memory amount to mis-report then it's possible you could have a knackered motherboard, CPU or even a pin in the LGA socket is bent, so maybe try re-seating your CPU and inspecting the socket for bent pins. This can happen because the memory controller is on-board the CPU.
 
The mobo and CPU _should_ be fine. Its brand new.

I tested both sets of 3 and they both show 6GB.

Is there anything else i can try before checking the CPU? Thats quite a major job removing the heatsink etc. I dont know where i put my thermal paste either.

Would it be safe to run it with 1 stick out for a few days?
 
Sure it's some kind of incompatibility. Try setting the memory speed to 1066 or 800Mhz. Obviously that's not ideal, but if it works it could help you track the problem down.

I really really doubt it's the CPU. They tend to either work or not.
 
your board sounds like it has faulty memory slots, try swapping them around, try 2 and not 4 and then try the other 2, trial and error. might be the memory.
 
I set it to 1066 and it said "over clock failed" then i had to go into the BIOS.

I set it to 800 and it worked but still reported 4GB.

Should i still have the voltages set how you said before? I haven't changed them back yet
 
Back
Top Bottom