• Notice regarding image hosts and attachments. See here.

  • Competitor rules

    Please remember that any mention of competitors, hinting at competitors or offering to provide details of competitors will result in an account suspension. The full rules can be found under the 'Terms and Rules' link in the bottom right corner of your screen. Just don't mention competitors in any way, shape or form and you'll be OK.

Please help MSI 7970 Lighting

Cheers for the advice guys, when I put the block on I tighten the screws very gently around the core and the whole block! Tho I did notice lot of themal paste around the circuit board! Can themal paste cause a short! I thought that stuff was non-conductive!

Thanks for help guys anyway, hope its not dead, but it seems that way!

Depends, but take it off and clean it up. When you fit new unknown heatsinks just put the smallest speck (1/4 of a rice grain) and hold the Heatsink in place with your fingers, it will tell you what sort of contact you have and help you realise how little TIM to use
 
What Tim did you use? Some can be slightly conductive.

Also did you fit the nylon washers?

Next step I suppose is to refit the stock cooler and see if the card is alive or not.
 
Well just fitted stock cooler and no luck, think I've blown your something, was so careful tho:(

Fitted into my bro's pc, same thing no power going into the card. GPU is only 2 weeks old as well!
 
Did you remove the Reactor on the back of the card to do all this??? Have you put it back correctly. If you did not remove it you have not crushed it have you????
 
Last edited:
I recon you crushed it to be honest. If you put it flat on its back and left the reactor on your asking for trouble.

You have tried different PCI EX cables I take it??
 
Tried different PCI EX cables, the reactor doesn't look crushed. Well I didn't get the card from overclockers from somewhere else so I'm going try and send it back, worth a try what can they say NO!
 
You can also completely remove the reactor, it may be worth a try.

If it doesn't work:

Refit cooler, double check EVERYTHING, that includes any scuff marks on screw heads, in general make sure it doesn't look 'tampered' with and if you get a replacement MAKE SURE TO READ THE INSTRUCTIONS a couple of times before and durring fitting the block, as you'll see once you read the instructions it does tell you to completely remove the reactor prior to fitting :)

Good luck!!
 
I have both reactor caps removed off mine. I never liked them but do like the LEDs so left them plugged in. I wasn't sure if they are needed though but CBA taking them off to see and I have only just put the sides and everything back in my computer for the umpteenth time :)
 
well card is cleaned and packed. Hopefully il get a replacement, but I'm taking as I wont!

I'm sure they will check to see if its been over-clocked or heatsink been removed!
 
You should be OK mate as long as there is no physical damage to the card. I know someone who rma'd a MSI card after changing the thermal paste and adding a new cooler. Just replaced stock cooler and sent it off and got a replacement. :eek:
mSI seem pretty good about RMA's.
Don't know what you did wrong but good luck next time.

Also they can't check if it was over clocked.
 
You should be OK mate as long as there is no physical damage to the card. I know someone who rma'd a MSI card after changing the thermal paste and adding a new cooler. Just replaced stock cooler and sent it off and got a replacement. :eek:
mSI seem pretty good about RMA's.
Don't know what you did wrong but good luck next time.

Also they can't check if it was over clocked.

Cheers! hopefully it all goes well
 
MSi are usually pretty good with cooler removals, they don't endorse or support it like EVGA do, but they aren't the ***** XFX are who plaster the thing in warranty stickers.

I doubt they'll remove the cooler in the shop, it should just be a case of visual inspection then try to power it up and send you a replacement. Provided they don't see any visible signs of it being removed all should be well.
 
Back
Top Bottom