Project: Temjin-S

Cleeecooo · 9 Aug 2011 at 14:43

Martini1991 said:
I was more on about the rioters

i know, but my 580 could sill take me out

Cleeecooo · 9 Aug 2011 at 20:35

KiiYzOo said:
hows the leak testing going?

perfectly

Sitting on the top of my computer now.

These bitspower fittings look soooo good! I need to get some more...

Cleeecooo · 9 Aug 2011 at 20:39

need some more 45's and compressions.

Cleeecooo · 16 Aug 2011 at 16:22

UPDATES AT LAST!!!!!

Well i'm £4 short of sleeving so I guess it will have to wait - again!

However, I've setup a loop outside my comp to test fro leaks and to flush the rad and try to clean some of the grime out from all my second hand bits :/

I am not using any of the new stuff (apart from rad an fittings) but here's the loop:

When the sleeving arrives, i'll take everything out of the case, start doing all the mods i'll need to do and I will also liquid cool everything when it is out of the case. Then, I will do the liquid cooling properly in the case when it comes back from the powdercoaters

Cleeecooo · 16 Aug 2011 at 17:12

KiiYzOo said:
why did you use so much tubing, having the pump down there?

1. to test its capabilities
2. it was the easiest placement

Cleeecooo · 16 Aug 2011 at 17:16

KiiYzOo said:
don't the cathodes hurt your eyes?

errrm no?

Cleeecooo · 16 Aug 2011 at 17:44

BUBBLES!!!!!

Cleeecooo · 17 Aug 2011 at 09:34

The 580 block is nickel an the 8800 block is copper.

Cleeecooo · 17 Aug 2011 at 21:39

Sleeving has been shipped

Cleeecooo · 18 Aug 2011 at 00:48

Thanks

Cleeecooo · 18 Aug 2011 at 09:49

Avathar77 said:
Are you going to use 480 and a 240 rad and the D5 pump at the bottom? Do you have enough space to put angled compression fittings(45 or 90?) after fixing the fans?

I'm using a thick 480 and a thin 240 and the 480 will have push/pull and possibly the 240 and i'll use angled compressions for those. The pump will sit at the bottom of the drive bays.

I'll see if the pump fits at the bottom with both rads though

Cleeecooo · 18 Aug 2011 at 10:23

Avathar77 said:
90 degree compression fittings?

sorry, a 90 degree with a compression on the end

Cleeecooo · 19 Aug 2011 at 08:35

RollerBall said:
Sounds exactly like my plans. Just I think I'll only be going for push or pull. Don't think both will fit.

Any idea how long until you do the tear down?

once I get back

I'll be going away tomorrow for 8 days

Cleeecooo · 2 Sep 2011 at 20:18

UPDATES!!!!!!!!

Sorry for the lack of chronological order

Cleeecooo · 2 Sep 2011 at 20:57

This picture deserves its own post

Cleeecooo · 2 Sep 2011 at 21:06

Hyburnate said:
I'm waiting...

So am I!

Stupid BT :mad:

Cleeecooo · 2 Sep 2011 at 21:20

Yeah yeah

Cleeecooo · 2 Sep 2011 at 22:16

posted pic

Cleeecooo · 2 Sep 2011 at 22:22

RollerBall said:
Now that you've taken it apart have you looked if you can fit Slim rad + fans/Fat rad + fans/pump in the bottom?

Sure, i'll do that over the weekend. Drop me a PM on the other forums if I forget tomorrow

Cleeecooo · 2 Sep 2011 at 22:42

ok, not good. not good at all!

Earlier, one of my LED strips' power wires wasn't secured and it short circuited and smoked and stuff.

Just now, the second one went. I'm going to return both. I got badly burnt trying to disconnect it