• Notice regarding image hosts and attachments. See here.

Q6600 Overclocking Help

Associate
Joined
31 Jan 2007
Posts
1,861
Hey,

I want to get my Q6600 to 3Ghz. I know that FSB x CPU Multiplier equals CPU speed so I am aiming for 334 x 9 = 3006Ghz

What I do NOT understand is what I have to do with the RAM. I do not understand about the divider and so on. I ahve looked at online guides and they all seem to explain it in different ways and it's really confusing me. If someone could explain what I need to do with my ram and what the divider is then it'd be most helpful.

My ram is: OCZ DDR2-PC2-6400. It says 4-4-4 on it too.

What does this mean? I am no good with RAM so could do with simple explanations if possible.

Thanks
 
ok, But how do you work out the divider? What is the calculation?

Also, how do you work out what speed your ram is running at?
 
fsbstraptonorthbridge.png


Hi rctneil

Here is the table of all the straps and associated ram dividers.

Now the straps are divided in 4 sections related to the fsb speeds and for each strap you have 3 ram dividers each having a particular dram to fsb ratio. E.g.

For the 333 MHz strap:

1st divider has ratio of 1:1 giving you ram speed of DDR2-667MHz
2nd divider has ratio of 6:5 giving you ram speed of DDR2-800MHz (which is default value in your case)
3rd divider has ratio of 8:5 giving you ram speed of DDR2-1066MHz.

It's giving you the formula for calculating the ram speeds:

Lets take 2nd divider for 333MHz strap as an example:

DDR2 speed = 2 x FSB x 6/5 = 2 x 333 x 1.2 = 799.2 = 800MHz

Now for overclocking your Q6600 to 3.0GHz; in the bios set the following:

-FSB Strap to Northbridge: 333MHz (as it is closest to your FSB of 334MHz). You can leave it on auto but i think it would just mean that you will get all the different ram speeds/dividers in your DRAM Frequency. Setting it to 333MHz ensures you get just the 3 associated ram dividers.

-FSB Frequency: 334MHz
-PCIE Frequency: 100MHz
-DRAM Frequency: DDR2-668MHz,DDR2-801MHz,DDR2-1069MHz

Choose the 2nd divider as highlighted although slightly overclocked. You can choose the first divider which will give you DDR2-668MHz (underclocked) if you want the ram factor to be taken out during overclocking although slight overclock of 801MHz shouldn't affect the overclocking process. This is what I did any way.

The 3rd divider gives you DDR2-1069MHz which is a highly overclocked ram and this is to be ignored. Otherwise choosing this divider means that your ram is already overclocked and this is highly likely to fail your overclock. I hope this helps:).

Edit: Here is the link from where I got the table. It talks about Asus ROG rampage mobo but I assume asus has the same bios overclocking options for skt 775 mobo as the Gigabyte does anyway.

http://www.anandtech.com/show/2427/4




Apologies for not replying sooner. I got stuck in talking on another forum about overclocking but not getting anywhere there so will try some suggestions from here I think (please bare in mind I'm not saying the advie on the other forum was bad or incorrect, just that I want to try elsewhere for the time being)

I first set my CPU FSB to 334 and set the vcore to auto and vcore to auto, set the pcie freq to 100mhz as suggested too. and it failed to boot.

It does the windows 7 startup animation and then bsods.

I then set the vdimm to 2.1 as that is reccommended by OCZ for my set. Intel gives a range of 0.8500v - 1.5v for the vcore but how do i know where within that range to start?

I also have the following list of options which I don;t really know what they are or what to set them too?

-FSB Termination Voltage: ops(auto, 1.2v, 1,3v, 1.4v, 1.5v)
-MCH Chipset Voltage: ops(auto, 1.55v, 1.65v, 1.75v, 1.85v)
-ICH Chipset Voltage: ops(auto, 1.05v, 1.20v)

-Microcode Updation: ops(Enable, Disable)
-Max CPUID Value Limit: ops(enable, disable)
-Execute Disable Function: ops(enable, disable)
-Enhanced C1 Control: ops(auto, disable)
-CPU Internal Thermal Control: ops(auto, disable)

I would appreciate it if you could give me a hand here.

Stock CPU temps are approx 25-30 C and my system is watercooled.

Mobo is Asus P5W DH Deluxe
Intel Q660 G0 stepping - bios 2206
OCZ DDR2-6400 $gb CL4 Edition

Thanks
Neil
 
ok, i'll give that a go. I take it i leave northbridge and southbridge at auto volts?

Also should i set ram setting to "from SPD" or set the timings and voltage manually?

Thanks

Neil
 
I set all the settings as described above and the vcore to stock volts of 1.25v and it bsods just after win7 animation. I upped the vcore a bit and same, then upped again to 1.3v and it does exactly the same.

Any other ideas?
 
ok, i'll clear the cmos and re enter all the settings above.

The PSU is brand new it's an Antec True Power New 750w

Yes, the pc works fine at stock 2.4. Basically, when i change the settings like you say, I enter them and save it in the OC Profile within the bios so when i want to use the pc normally without trying to overclock, i can restore defaults and use the system fine. then when i want to go back to when i was messing with oc settings i just restore from the profile i saved.
 
Just reset cmos and set those settings and it's booted. gonna check coretemp and cpuz now.

VID is 1.25v.

Temps now (just after startup are between 23 - 30 celcius)

CPU-z is saying running at 3ghz which is great news.

Thanks for helping me sort it.

I do want to ask, when moving the jumper to reset cmos, do I really needto remove the battery like the mobo manual says? if so then fair enough but if not then it'll be helpful as i have to remove my gpu to be able to access it!
 
He used 334 x 9 just as I did.

334 x 9 = 3006MHz = 3Ghz (Solid 3.0GHz)

333 x 9 =2997MHz = 3Ghz. (dubious 3.0GHz lol:p)

I have noticed many times when people use 333 x 9, in the cpu-z it is showing mainly as 2997Ghz and they are calling it 3Ghz. Best to use 334 Mhz:).

I did actually use 333 after resetting cmos last night but have changed it to 334 this morning before booting.

CPU-Z is stating i'm at 3009.8Mhz. When i was at 333 cpu-z said 3002.?Mhz

Odd eh!

Thanks

Neil
 
oh sorry, that screendump doesn't show the ram, i'll check now and update post in a min

Just checked the cpu-z validator site andjust noticed it does say ram speed on left side.

Sorry for the confusion:

RAM : 4096 MB DDR2 Dual Channel
RAM Speed : 334.4 MHz (1:1) @ 5-6-6-18
Slot 1 : 2048MB (6400)
Slot 1 Manufacturer : OCZ
Slot 2 : 2048MB (6400)
Slot 2 Manufacturer : OCZ
 
Last edited:
right, i'm on my netbook posting this as my desktop is sat in the bios screens. For RAM i get options for:

501
668
835
891
1002
1113
1336

The multiplier is still locked at 9

Why isn;t it giving me 801 like you said?



Also, a bit off topic but bios related:

When i boot my system, I get a message saying Detect Drives Done, no drives found.

Why does it say this?, i have my os drive in sata 0, storage in sata 1 and optical drive in sata2

on main bios page, it says:

Primary ide master: not detected
primary ide slave: not detected
third ide master: wd150gb
third ide slave: wd500gb
fourth ide master: not detected
fourth ide slave: optical drive

Any ideas about this?

Thanks

Neil
 
ok, thanks about the hard drives, i'll post elsewhere to ask.

I can't seem to find that fsb strap to northbridge anywhere. Will it be under a different name?, I can't find anything that could be it either?
 
ok,

Here's 3 photos which hopefully will be of some use:

Photo%20Dec%2017%2C%2011%2034%2046%20PM.jpg


Photo%20Dec%2017%2C%2011%2035%2025%20PM.jpg


Photo%20Dec%2017%2C%2011%2036%2002%20PM.jpg


Sorry, can't resize them as i took them on my phone and sent them to dropbox and put the public link on here.
 
If I set the FSB to 333 then the options change to:

500
667
834
889
1000
1111
1334

I am pretty sure that before the CMOS reset, I could get 800 to show up. (not 00% about this though) It's odd.
 
Back
Top Bottom