VM Superhub Firmware

Admiral Huddy

Admiral Huddy

Admiral Huddy

Man of Honour
Joined
17 Feb 2003
Posts
29,640
Location
Chelmsford
I swapped out my old Router/Modem combination for one of these last weekend to take advantage of the 30MB connection. I'm quite pleased with only having the one device but I've noticed a few quirks / limitations.


Firstly, it appears that some wireless devices keep dropping. In particular my sons XBOX which had no problems before. Sound familair?

Secondly, I controlled all wireless devices from my old WRTGl with Tomato firmware. The new device has MAC filtering but it doesn't toggle over midnight. I'd like to disable wireless access on a device-by-device basis retricting access to certian times but the VM hub won't allow me to disable between 8pm to 8am next moring.. the Tom firmware did.

My questions are

1. Does any one know how I can get round this?
2. Can the software by updated or replaced?
3. Is there any means I can activate some kind of access control other than from the hub itself.. It's becoming a full time job as a network administrator at home..


Thanks
 
I have to agree.. I was looking forward to only having one device rather than the two.. I looks like R28 addresses quite a few issues but it's still only beta:

I found this via Google:



This is a list of all the feature requests we are currently examining to see if we can include them in a future firmware update. They were taken from this thread on the main forum.

We've not finished our investigation into if it's practical for us to include all of these in the Super Hub firmware, but we do hope to include as many as possible. This list is here to show you the features we're already looking at so you don't need to request them again.

Also to speed the availability of Modem Mode (Bridge Mode) these features will not be included in that firmware update available in the near future. When we have more information on which features will be selected and when they'll be available I'll post it on the forum.


Feature requests for Overlay GUI


•Add Super Hub reboot option
•Increased overlay GUI timeout (also add user defined option) - This is currently 180 seconds, needs to be minimum of 360 seconds and/or user defined
•Link to VM Speed Test tool

•Visual confirmation of 'connect speed' for upstream and downstream

Feature requests for Advanced GUI


•Add Modem Mode (Bridge Mode) - Ability to place the Super Hub in 'dumb modem' mode
•Remove reboot after reserving a LAN IP - Currently, the Super Hub reboots after every LAN IP is reserved. Should be able to add multiple before applying the setting and rebooting the Super Hub
•Add DDNS support - Ability to set-up DDNS services
•Add ability to specify alternate DNS - Ability to set an alternate DNS on Super Hub, used for 'OpenDNS' type services
•Add Quality Of Service (QOS) functionality - Adding a QOS feature that will allow certain traffic to be prioritized
•Add ability to directly access 'Advanced' GUI via unique URL - So instead of entering 192.168.0.1 (or http://routerlogin.net) you could enter 192.168.0.1/advanced (or http://routerlogin.net/advanced)
•Add Channel adaption technology (Smart Wireless) - Ability to monitor frequency noise and change channel on the fly in order to move to a less saturated frequency
•Add ability to dim/switch off LEDs
•Add ability to configure VPN
•Add ability to monitor Bandwidth & usage
•Add Wake On LAN (WOL) functionality - Ability to wake up connected (but powered down/sleeping/hibernating) device
•Access to signal levels without having to log into GUI - Ability to access http://192.168.0.1/RgConnect.asp without logging into GUI
•Provide SNMP Monitoring - Provides ability to monitor LAN side settings (not WAN side) - i.e. bandwidth, CPU load, RAM etc… generally read only
•Add Network Time Protocol (NTP) functionality - Retains accurate time by linking to online time service, also provides ability to synchronize clocks on all devices across the network
•Add Port Address Translation (PAT) functionality - PAT translates TCP or UDP communications made between hosts on a private network and hosts on a public network. It allows a single public IP address to be used by many hosts on a private network (LAN)
•Add ability for user to adjust remote access timeout for SSH etc…
•Add ability to toggle port forward settings - Currently have to delete and re-enter if you wish to temporarily disable a setting
•Add ability to view same stats as on the VM300 - For example: Correctable codewords, Uncorrectable codewords, Total codewords received, Upstream mini-slot size, Interleave data if it's not standard across the network, etc...
•Allow MAC auto-population - For area's where a MAC address is to be entered (i.e. LAN IP area), allow MAC of connected device to be selected and auto-populated - will reduce input errors.
•Allow more than 10 pings to test connectivity.
•Improved logs - Add Device power cycle, firmware updates, dropped connections, ports/services blocked, etc...
•Configurable INTERNAL IP Lease Time
•Add confirmation prompt prior to any reboot attempt.
Click to expand...


Add Modem Mode (Bridge Mode) - Ability to place the Super Hub in 'dumb modem' mode - Looks interesting.. Still as You said, I'd rather have the all-in-one I've paid for.
 
R30 updated to hub last week. Didn't know till last night.

I've seen the new option to use the hub in "Modem only" mode but not tried it yet.

Anyone noticed any performance differences?
 
You must log in or register to reply here.
Back
Top Bottom