The name of this new beta bios is "P67 Extreme6(142)"
Bios file name is "P67EX61.42"
Direct Download link here http://europe.asrock.com/downloadsite/bios/1155/P67 Extreme6(142).zip
Did You get your board back to life ?
Got my Asrock P67 Extreme 6 up & running now.Any questions u want answered
- Thread starter chaparral
- Start date
Did You get your board back to life ?
Only setting the short and long power higher will allow it to hold higher multipliers, I upped long duration from 95 to 110, what do you have ?
side note, I have had a couple of bluscreens in prime now
Chucked mine up to 250 on all 3
ok checked bios when i got in and its at default 150 i say default cause i havnt touched it, everything else says auto
while i was there i dropped offset to -0.06 cpu z now reports between 1.28 to 1.328 primes been running for half hour so far and temps still hitting 75 average 1/2 & 71 0/4
anyone know how long artic silver ceramique takes to bed in?
while i was there i dropped offset to -0.06 cpu z now reports between 1.28 to 1.328 primes been running for half hour so far and temps still hitting 75 average 1/2 & 71 0/4
anyone know how long artic silver ceramique takes to bed in?
No...I tryed again last night with no luck..
No...I tryed again last night with no luck..
bummer, still guess most of us will be without for a short time now asrock have confirmed exchanges should be due v shortly
Thank's, Life is easier with the presets as a base....You have a good chip there
but I don't rate the cooler much ! My Noctura with 1 fan held below 70 at -.05.Not sure ceramique needs to bed in as it's not silver particles like AS5 also I thought not as good....could loose a few degrees for You with AS5
what preset r you running now?? a few peeps have the h70 with vipers and oced sandys supposedly not hitting 50 so i think im gonna grab some as5 from work tomorrow and try reseating, also i think i may put the corsair fans back on as the pc is in a different room to where i am sat so pwm function dont really matter.....in fact thinking about it now i dont even know why i changed them!
Mate, You would not believe I have 11 A4 sheets from testing !! if You use full manual settings You can get the job done about 3 different ways
I'm now playing with the presets, 4.8GHZ is too much voltage and temp for My liking, so playing with 4.6 with offset volts and LLC + PLL which now works
It's needing about 1.28v loaded for prime which is the wrong side of 1.3 med load.I'm pleased with My Noctua C14 which I have modded to 1 fan blowing up from the bottom, besides it cooling the mobo, from 60c if you take the load off it's back in the 30's in literally 3-5 sec....never seen a cooler do that
Last edited:
Posted (RMA) my motherboard back to OCuk today...My motherboard is now failing to boot...does not even get to the bios screen
Tryed pulling out all memory and swapping slots & tryed using single stick in each slot..
Tryed clearing the cmos by rear switch & jumper on board
Tryed removing battery
Tryed with only a single GPU card (both slots)
Tryed with all USB items/cables ,network cables, hardrives etc,etc removed
And still does not work
(Now using my old 775 board & CPU)
Looks like it RMA time for my Extreme 6....
Wonder how long it be before i receive one back...
So once your board goes back are you going to get the same board or would you swap for another ?
I asked for it to be replaced with the same board...
Got this reply back from OCuk
Looks like it must be my CPU or ram that is faulty...
Am going try test my i7 CPU & ram tonight in my new SB HTPC
Not the first time I've seen that, taking everything off the board and leaving for a day or so, or just re-mounting the CPU and it's back to life, It was just the cmos that was a little scrambled.
Surely a waste of time getting it back when the replacements should only be a few weeks away ?
Surely a waste of time getting it back when the replacements should only be a few weeks away ?
Seems like it my i7 cpu that is faulty as the HTPC i have just built will not boot at all with my i7 2600k cpu.......But boots fine with my i5 2500k
I Just been on the phone with OCuk for my CPU RMA
And they mentioned something about ASrock will not send them any B3 boards for replacing are B2 boards
Ocuk said we need to contract Asrock are selfs to try get are boards changed..
Last edited:
Soldato
- Joined
- 18 Oct 2002
- Posts
- 8,307
- Location
- Aranyaprathet, Thailand
I've seen some with V3 but when I questioned them they admitted that this is not the same as B3.
Ones I have seen are B3 versions, anyway easy to tell if you got the new B3 version it says so on the box,
http://www.asrock.com/news/events/201102ex/warranty.html