8 PACK MEMORY RANGE GROWING: SAY HELLO TO 8 PACK RIPPED EDITION & 32GB KITS!!!

Servo · 19 May 2020 at 15:28

Did you reset the bios before changing the memory? Maybe put the old stuff back in and set the memory to 2133 1.35volts then change back to the new

wookiee87 · 19 May 2020 at 15:28

doodah said:
So I just installed the 3600 C16 along with my new 3700X and I'm getting an OD error code with no POST. I'm on the latest BIOS for my CH6 and it POSTs fine when I put my Trident 3200 C14 back in. Any ideas?

try upping the soc voltage in the bios around 1.050 - 1.1v max see if the pc boots, don't go above 1.1v as you may degrade the memory controller on the cpu

doodah · 19 May 2020 at 15:58

Thanks, have tried both (though only 1.05 for the SOC voltage so far) but I still get the error.

wookiee87 · 19 May 2020 at 16:09

doodah said:
Thanks, have tried both (though only 1.05 for the SOC voltage so far) but I still get the error.

are you able to test the new ram in another machine and replicate the error?, if so i'd say the ram is bad which would suck

Servo · 19 May 2020 at 16:12

hhmmm try one stick of the new stuff. if it works, remove and test the other

doodah · 19 May 2020 at 16:25

wookiee87 said:
are you able to test the new ram in another machine and replicate the error?, if so i'd say the ram is bad which would suck

I can try it in my HTPC

- will do so after a quick shop.

Servo said:
hhmmm try one stick of the new stuff. if it works, remove and test the other

Tried that, still no luck. Leaning towards defective stick at this point.

opethdisciple · 19 May 2020 at 16:34

Do you have any custom timings set on the old ram that is trying to be applied to the new stuff?

Reset bios to defaults, put the new ram in and it should start up at default speed and voltage.

doodah · 19 May 2020 at 16:52

I was running it on XMP for the Trident (DCCOP or something like that), no other tweaking. I've cleared the CMOS and tried loading optimized defaults.

Skynet5 · 19 May 2020 at 19:38

Worryingly that is a couple of issues with this ram.

QC goes down during covid obviously.

Meridiusuk · 23 May 2020 at 07:47

Hi all I have 4x8gb 3600c16 ram 8 pack which i bought last year at XMP settings on a gigabyte master with a 3900x, would the ripped 3600c14 versions make that much difference compaired to these in performance ?

I have not even tried to get the fram to 1:1 one yet which is 3733

thanks

Troezar · 23 May 2020 at 08:01

Meridiusuk said:
Hi all I have 4x8gb 3600c16 ram 8 pack which i bought last year at XMP settings on a gigabyte master with a 3900x, would the ripped 3600c14 versions make that much difference compaired to these in performance ?

I have not even tried to get the fram to 1:1 one yet which is 3733

thanks

I wouldn't think you'd see a huge difference, bigger impact going 1:1. I can say the C14 ripped are good, my system feels very quick andaand responsive. It all depends on your spare cash if it's worth it to you.

doodah · 23 May 2020 at 18:25

Eventually tried the 8Pack 3600 C16 in my HTPC - worked fine. I then tried it back in my main rig - worked fine

.

Not sure why the initial hiccup (no POST/0D code) but sitting at 3600MHz along with my new 3700X :cool:

- now some fine tuning

.

Skynet5 · 23 May 2020 at 18:28

Meridiusuk said:
Hi all I have 4x8gb 3600c16 ram 8 pack which i bought last year at XMP settings on a gigabyte master with a 3900x, would the ripped 3600c14 versions make that much difference compaired to these in performance ?

I have not even tried to get the fram to 1:1 one yet which is 3733

thanks

Undetectable I would say in general usage. A tuned 3600 c16 kit will be better than an untuned 3600 c14. So tighten those secondaries.

Troezar · 23 May 2020 at 18:31

lnoton said:
Undetectable I would say in general usage. A tuned 3600 c16 kit will be better than an untuned 3600 c14. So tighten those secondaries.

Good advice, I'm going to look at the ones you mentioned previously once I get this garden finished

Meridiusuk · 24 May 2020 at 07:42

thanks for the help, is it poss to get my ram to 3733 @ c16 or C14 ?i have all four slots used as i have 4x8gb

ram i have is
https://www.overclockers.co.uk/team...3600mhz-dual-channel-kit-black-my-08q-tg.html

cheers

Space Monkey · 24 May 2020 at 16:23

I've not read through a lot of the last few pages fully, so if this has been mentioned then please ignore me

I was just curious to see what settings I could get out of the Ryzen DRAM Calculator with these 3600C14 sticks and noticed an amazing set of figures in the bottom left box where it shows RAM quality etc! Best I've ever seen :eek:

Skynet5 · 24 May 2020 at 16:33

Space Monkey said:
I've not read through a lot of the last few pages fully, so if this has been mentioned then please ignore me

I was just curious to see what settings I could get out of the Ryzen DRAM Calculator with these 3600C14 sticks and noticed an amazing set of figures in the bottom left box where it shows RAM quality etc! Best I've ever seen

Crikey
Is that after you've imported thaiphoon?

GregI · 24 May 2020 at 16:36

Space Monkey said:
I was just curious to see what settings I could get out of the Ryzen DRAM Calculator with these 3600C14 sticks and noticed an amazing set of figures in the bottom left box where it shows RAM quality etc! Best I've ever seen

That's an interesting score but I feel like it's bugged or something. The G.Skill C15 kit I have was 100 and 4600 C16. You would assume 100% would be a maximum score.

What's the screenshot for the Main tab Fast preset looking like? I wonder if it will also recommend 14-14-15-28 at 1.45v

Space Monkey · 24 May 2020 at 16:38

lnoton said:
Crikey
Is that after you've imported thaiphoon?

Yep, if you look at the top right hand corner, if it shows the ram info above the Help & About buttons then its been imported!

Space Monkey · 24 May 2020 at 16:41

GregI said:
That's an interesting score but I feel like it's bugged or something. The G.Skill C15 kit I have was 100 and 4600 C16. You would assume 100% would be a maximum score.

What's the screenshot for the Main tab Fast preset looking like? I wonder if it will also recommend 14-14-15-28 at 1.45v

I'll have to run it again to check.

Strangely enough I've just downloaded version 1.7.3 and it no longer populates the RAM Quality rating section, does anyone else have this issue? Maybe my RAM is too much for it to handle