Black 'n' Blue MK2 - Watercooled Bitfenix Prodigy

reiyushin · 12 Jan 2013 at 17:15

Oh busy busy busy!

I keep running into snags, I guess it's to be expected with the small case

Anyways, the second window is but and I've got some more sleeving done, got the rads installed but then I ran out of space o.O The pump is homeless at the minute so I'm going to drill it a home in the back of the case, I'll need to get some more angle fittings to make the layout work...the last ones I had leaked, I dislike angle fittings!!! >.<

reiyushin · 12 Jan 2013 at 19:28

Some pictures of the second window

Masking it out

Cutting and mess

Nice acrylic and sticky tape

Done

reiyushin · 13 Jan 2013 at 13:32

Doing some cable sleeving this morning and looking at LED strips

Akagi · 17 Jan 2013 at 14:43

You might be able to get the cuts in the windows straighter if you sand/wear them down, maybe with a straight-edge fastened there as a guide to ensure you dont go too far.

Looks amazing as is though

Interested to see it finished

ChrisLandin · 17 Jan 2013 at 21:00

Those fans look epic, again! Wish I still had them now for my Lian li v351 modded build I'm doing.

Your case looks excellent by the way. Well done.

Is it quite easy using a dremmel? I'm still on my jigsaw lol

Tokin · 18 Jan 2013 at 20:11

Cant wait to see this one finished!

reiyushin · 18 Jan 2013 at 22:18

acme15 said:
You might be able to get the cuts in the windows straighter if you sand/wear them down, maybe with a straight-edge fastened there as a guide to ensure you dont go too far.

Looks amazing as is though

Interested to see it finished

Yea I might give that a go at some stage

thanks

ChrisLandin said:
Those fans look epic, again! Wish I still had them now for my Lian li v351 modded build I'm doing.

Your case looks excellent by the way. Well done.

Is it quite easy using a dremmel? I'm still on my jigsaw lol

Cheers

Yea a dremel is easy enough, just take your time with it.

Tokin said:
Cant wait to see this one finished!

Thanks

I hope I'll get the watercooling in on Sunday!

reiyushin · 23 Jan 2013 at 20:10

A lot more work has been done

First up the GFX

ooo00ooo0o0oooo shiiinneeeeeeyyyy D

Stripped, cleaned, MX-2 Applied amd thermal pads on

Voila

reiyushin · 23 Jan 2013 at 20:29

Mounting the pump, who can see the mistake? XD

Doomedspeed · 23 Jan 2013 at 21:11

reiyushin said:
Mounting the pump, who can see the mistake? XD

The motherboard has turned invisible leaving you with a floating backplate.

supergluechris · 23 Jan 2013 at 21:53

REMOVE THE PLASTIC FROM THE GRAPHICS CARD

alkhjflkashfas

Tattysnuc · 24 Jan 2013 at 08:13

Reservoir inlet/outlet port at the base of the res will interfere with the side panel?

Sam37 · 1 Feb 2013 at 13:43

He has it all done now, it looks great, update the thread!

IC3 · 21 Feb 2013 at 00:40

Very nice build, would love to change to one of these. But I will probably go for one of these once I upgrade my cpu.
Any new updates? You could post a picture of current work you did ;]

wobbledog · 22 Feb 2013 at 15:44

this has to be the most impressive Prodigy build I've seen

Deceptor · 22 Feb 2013 at 19:24

Nice job! Can't wait to see the final result

Anox · 22 Feb 2013 at 19:51

All those toobz, it's gonna be a tight jam for sure.

reiyushin · 9 Apr 2013 at 17:09

I've just been told to update this

I'm 95% done on this just a few wires and little things to do, I'll get some pics up

reiyushin · 9 Apr 2013 at 17:38

The mistake in that pic was that the pump was the wrong way round

I had both inlets in use but no the outlet...derp.

reiyushin · 9 Apr 2013 at 17:59

Getting it all tubed up!

This one didn't resize so it's in spoilers ^^

I massaged out this kink and used a cable tie to keep it nice and round

Ready to go......

but nothing happened

Stuck with this... >.<

More later