Nice to walk into a package when you get home..

Mekrel

Mekrel

Mekrel

Soldato
Joined
2 Aug 2004
Posts
8,352
Location
Buckinghamshire
Got home today, wasn't even expecting this untill Wednesday!

Picture%20001.jpg


Picture%20002.jpg


Picture%20003.jpg


Plan is to installed a dual watercooling loop into it, have the innards powder coated black.

PA120.3 in the front of course, and a PA120.2 in the top me thinks.

Not sure exactly how though, any ideas?

I'm a bit of a perfectionist.
 
Looking good mate!

Need to get a couple of the hard drive bay adapters Lian make in the bottom of the two drive bay piles to break the look up a little in my opinion.
 
Hefner said:
Jealous!

I fancy myself one of these instead of a MountainMods case, but the cost of all the necessary bits soon adds up.
Click to expand...

Glad to see someone else who likes these over mountain mod cases. Know a PC repair shop owner who has a MountainMod case powder coated black and you can tell it's something that's been created. It has that "amature" kinda look to it, I can't put my finger on it.

Gotta try and plan my work so that I can visit my local supplier to pick up a pump :)
 
Mmmmm

I have to admit to being just a bit envious. I did work out the cost of one built-up to my preferred spec. and it came to almost £700 for the case, 120.3, 120.2, mounting brackets, HDD brackets, fan brackets and grills.

I'm almost convinced!
 
WJA96 said:
Mmmmm

I have to admit to being just a bit envious. I did work out the cost of one built-up to my preferred spec. and it came to almost £700 for the case, 120.3, 120.2, mounting brackets, HDD brackets, fan brackets and grills.

I'm almost convinced!
Click to expand...

At that price its a bargain... :D

Not seen one first hand yet so could do with taking a peek sometime.... *big hint Mekrel*
 
Ha!

Well you can always help me mod it if you wish :) and can always come up to you if you got the room. On the weekends of course.

Sent a design off to a cutting company today (well yesterday but it bounced, went through today fine though).

grill.jpg
 
Interested to see how this goes,that`s the case i plan to buy for my own new build,if i ever get time away from doing them for everyone else i know :rolleyes:
 
WJA96 said:
Mmmmm

I have to admit to being just a bit envious. I did work out the cost of one built-up to my preferred spec. and it came to almost £700 for the case, 120.3, 120.2, mounting brackets, HDD brackets, fan brackets and grills.

I'm almost convinced!
Click to expand...

Might take a while, but you will be convinced after you see the end result for this :)
 
Im planning to get one of these soon aswell.

Again i prefer it over the Mountain Mods because its kinda more stylish. Only shame is there is no Mobo tray.

Can you give me the dimensions of *** top panel as i want to figure out what rad configurations you could get in there? Like a pair of 120.2 or would a 120.3 squeeze in...?

Cheers
 
You could get a PA120.3 easily in there, but you would have to go across the full top removeable plate. Aint had chance to really mess about with it yet to see whats what, been busy with work this evening. There is a mobotray and it is screwed into the back as if it were removeable, but then there is a bracket connecting it to the 5.25" bays so I guess not?

Will find out tomorrow.

I would suggest, PA120.3 in the front, with A16 like meshed 5.25 plates.
 
ok cool thanks for answering.

Just one thing though when you get your work log going could you just take a picture of your 120.3 by the top panel so i can get an idea of scale?

Thanks in advance.
 
You must log in or register to reply here.
Back
Top Bottom