Not passed ,3d mark

Associate
Joined
24 Jun 2004
Posts
787
Location
Carnoustie
Can someone help out please
I'm getting a pass 94.2 not passed on my 3D mark test [fire strike extreme test ]

And that's about all it says
Any ideas how i can find out what's failing to get to a pass mark of 97 please
 
Associate
Joined
20 Jun 2013
Posts
1,830
What is your card and do you have any overclock on it? what is your psu, and what are your temps on your gpu and cpu?
 
Associate
OP
Joined
24 Jun 2004
Posts
787
Location
Carnoustie
Hi
ive got my drivers updated yeah

i have a zotac 2080ti ,no clock on it
psu is a phanteks 750 [just bought yesterday]
temps are 40 and 45 but thats not in game


cpu in game is running nearly 90
 
Associate
Joined
20 Jun 2013
Posts
1,830
I take it you're running the stress test, can you see what temps you are getting on your 2080?
I would guess that it's your card throttling due to heat that is causing the failure, put your fans speeds up and see. the test isn't designed to be run back to back because you're looping 20 tests together which is more stressful then normal gaming
 
Associate
Joined
18 Jan 2012
Posts
854
Location
Peloponnese, Greece
I take it you're running the stress test, can you see what temps you are getting on your 2080?
I would guess that it's your card throttling due to heat that is causing the failure, put your fans speeds up and see. the test isn't designed to be run back to back because you're looping 20 tests together which is more stressful then normal gaming
Exactly this, the stress test is designed to 'measure' if your PC throttles at all during the test. It doesn't mean you have a problem, just that the hardware is being restricted in some way.
 
Associate
Joined
20 Jun 2013
Posts
1,830
It would be like running Prime95 on an hour long loop with Avx enabled and wondering why there's a burning smell, not all tests are required for a stable running system
 
Associate
OP
Joined
24 Jun 2004
Posts
787
Location
Carnoustie
the gpu was running roughly at 80 thats with the case open

I only ran the test once

The problem ive been getting is random crashes [Cod] so ran these tests to see if i could get a pointer
 
Associate
OP
Joined
24 Jun 2004
Posts
787
Location
Carnoustie
Its hard lock ,system restart

my fans were running at standard CPU 1520, CHA 1143 ,AIO pump 1439

ill set them to full and check again

full is now CPU 1683 , Cha 1717 AIO is unchanged
 
Associate
Joined
20 Jun 2013
Posts
1,830
Have you got HWinfo? Maybe have that up and running so you can see what your GPU and CPU temps are like.
 
Associate
OP
Joined
24 Jun 2004
Posts
787
Location
Carnoustie
If downloade it and im running it now temps seem to be fine [again ive taken the top of the case
]
I dont know if its me ,but the way the rad and fan are mounted ,it facing the top of the case ,right into the glass
 
Associate
Joined
20 Jun 2013
Posts
1,830
you'll need to link it through imgur or some website like that, but try running without the side on your case so you 2080 gets to vent the hot air and see if you crash on a days gaming.
 
Associate
Joined
11 Jan 2016
Posts
2,356
Location
Surrey
Can someone help out please
I'm getting a pass 94.2 not passed on my 3D mark test [fire strike extreme test ]

And that's about all it says
Any ideas how i can find out what's failing to get to a pass mark of 97 please

As long as it is complete it is fine I think. The stability is about how close the average frame rate across all runs are. If you have wildly different temps from 1st run to last run then that can cause instability as you will get higher clocks and higher FPS at the beginning and lower towards the end and this will cause the % to decrease.
 
Top Bottom