**Official Abit Fatal1ty FP-IN9 SLI NF650i Owners Thread**
- Thread starter AFK_Matrix
- Start date
Got hold of a L632B CPU which shows further improvement on this board.
Although stable i won't be running at this speed as temps are a little on the high side.
Seems to hang around low to mid 50's - load but after checking logs it did peak @ 65c.
Also getting 1 or 2 cold start probs needing a reset and then to reset bios FSB settings. (this is with latest bios 12)
L636B i had was giving me the following with 1.550v vcore set in bios (1.52v load)
Temps were a fair bit lower on 36B even though slightly more voltage.
Last edited:
Soldato
65c is perfectly safe btw, Ive been there and above since xmas, 24/7
"chipper36....what cooling do you have m8 ?
Those are pretty good temps you got there !"
Tuniq Tower and a fair few case fans.
"65c is perfectly safe btw, Ive been there and above since xmas, 24/7"
yeah i probably could run it with them temps and lower vcore a bit further too.
had it booted @ 3.8GHz earlier with 1.550v (bios) and could run Super-PI 32m test ok but orthus failed around the 1 minute mark.
These 32B stepping chips seem pretty decent anyway
Those are pretty good temps you got there !"
Tuniq Tower and a fair few case fans.
"65c is perfectly safe btw, Ive been there and above since xmas, 24/7"
yeah i probably could run it with them temps and lower vcore a bit further too.
had it booted @ 3.8GHz earlier with 1.550v (bios) and could run Super-PI 32m test ok but orthus failed around the 1 minute mark.
These 32B stepping chips seem pretty decent anyway
Soldato
Sounds great, 3.8 is very good.
1min orthos is stable enough to run just about anything in my experience. On the other hand Ive heard people say they run orthos for 5 hours and it still randomly fails.
Even a program at 100% using both cores wont stress like orthos does so 1 min is enough imo. Its not like you'd really notice a couple hundred mhz for every day use though really
1min orthos is stable enough to run just about anything in my experience. On the other hand Ive heard people say they run orthos for 5 hours and it still randomly fails.
Even a program at 100% using both cores wont stress like orthos does so 1 min is enough imo. Its not like you'd really notice a couple hundred mhz for every day use though really
lol yeah must admit i am getting a little bored running orthus over and over again (need an excuse to stop it).
when i was @ 3.8 i noticed my idle temps were way up around 40c but all over the place. only tried running 1 super-pi @32m and temps were under 50c.
I might lap the cpu if i can be bothered, not too sure if it would improve it as this chip looks a lot flatter than my 36B i had.
when i was @ 3.8 i noticed my idle temps were way up around 40c but all over the place. only tried running 1 super-pi @32m and temps were under 50c.
I might lap the cpu if i can be bothered, not too sure if it would improve it as this chip looks a lot flatter than my 36B i had.
hi all i have just got rid of my ASUS P5N-E SLI well 2 of them both bad so i am geting this it looks ok has some good points that i like but it also has some of the problems the first one has
so setings to get me started
eny onfo would be great thanks will post back when i get it
sc00t
so setings to get me started
eny onfo would be great thanks will post back when i get it
sc00t
Soldato
I'll give you a week to get the P5N-E SLi out again. 
WJA96 said:I'll give you a week to get the P5N-E SLi out again.
no it one hell of a bad board its made by getting cheap parts and its support is well there is none
i was told by asus to take off my bios chip they got me to pay for one to be sent from the USA so i did even though i told them it don't come off
and i have had 2 more that have just not worked
last one well it just would not boot
fans spin yea but no beep for no video or mem and no output to monitor
so if this one don't work it mean i wont be keeping it but it do not mean i will go back to asus well the one thats made by bluepeter :/
sc00terx
WJA96 said:I'll give you a week to get the P5N-E SLi out again.
i would not go back to that board till they it out
board i have now works well and it still needs a new bios imo but all the board with this chipset are not as good as they could be
sc00terx
Associate
what kind of fsb are people getting upto??
I am looking at getting this and a C2Duo E6550
I am looking at getting this and a C2Duo E6550
Soldato
lol ignore me 
Soldato
I am having a few problems with the nvidia sata drivers.
Can someone that has had no problems with sata drivers double click on the Nvidia nForce Serial Ata Controller and post a pic so I can see if its the same as mine when I open the properties.
Does the below look right?
Can someone that has had no problems with sata drivers double click on the Nvidia nForce Serial Ata Controller and post a pic so I can see if its the same as mine when I open the properties.
Does the below look right?