• Notice regarding image hosts and attachments. See here.

Please Help - GPU wont fit.

You don't need to worry regards the 8 pins, just the SATA Power and data lead going to the motherboard.
 
Right. Im just trying to work out the front panel functions slots but i think i got that. However where does my case fun plug in? It seems to have 2 head both of which could likely be plugged into each other. quite large 4 pin male and female. there is a "sys fan" slot on my mboard but it is 4pin male and tiny by comparison?
 
These would need to be plugged directly into the PSU via the molex PSU lead, what case did you go with in the end?
 
Cooler Master Silent Pro Modular 600W '80 Plus Bronze' Power Supply

Ok this is the siutation

PSU into motherboard ( massive 20odd pin plug)
PSU to CPU (4 pin connecter near the cpu)
PSU to HDD to CDROM (All 1 cable)
2x PCI 6+2 pin cables from PSU To GPU using the 6pin heads and leaving each 2pins head dangling.
Front case LEDS and power into 1 block on the Mboard called JFP1 (this was fiddly)
Red cable from HDD to Sata port on Mboard
Red cable from CDROM to port next to the sata port
1x molax cable from PSU that plugs into ONE of the heads of the system fan at the fron of my case. Leaving the female system fan head free.

Does this look okay? If so im gonna use a few cable ties and am i ready for the big bootup when i connect monitor etc?
 
I would say your looking ok, one thing I tend to do before starting the system is doing a CMOS reset.

You can do this by shorting two pins on the motherboard together by using a jumper (supplied on the board) or screw driver, the manual will show location.
 
Ohh i just found 1 cable with 2 head that reads
"AC97" "HD Audio"

On each head. Also i have a small cable with no label that has a very small female socket on both ends that is clearly for use on Mboard somewere?


ohh the double female one is labeled "usb"


Best guesses at functions of these cables?
 
my mboard has USB and Audio already build in to it, im guessing these cables are for if you have extra jacks/usb ports etc at the front of your PC case?
 
The Audio cable goes to the front panel of the case to allow headphone and mic use, this plugs into the top of the board by the pci slot.
 
But i do not have headphone slot or any sort or port the the front of my case. All ports are at the back and feed directly into the Mboard itself so do i need to use these?

Thanks so much for your help mate.
 
Did you go with the Antec 300 case, the headphone and mic jacks are next to the USB ports.

Not really, the USB ones will be handy for the front of the case :)
 
There are 2 small jacks at the top of the case which the mic and headphone jacks, right in-between the two USB ports.

Unless they have changed it!

I think your ready!
 
indeed hahaha well thats plugged in thanks so much I have learned A HELL OF a lot today so quite chuffed.

The ac97 didnt have a place to go so dno whats going on there but the HD audio went in its place as did the USB so gonna refit side panels and prepare to boot XD
 
I turned it on and no bang.

A few issues.

The CD Drive will not open when i press the button.
On the Bios main menu the Listing for every sata port says "Not present"

Does this mean i didnt setup the HDD and CDrom properly?
 
You can use any sockets for these.

I assume you herd the hard disc drive ramp up and did you hear any noises from the DVD drive when booting.

Might be worth shutting down and double checking the power leads are in, they could have been moved when doing some other cabling, i have done this on many occasion.

I'm signing off now, hopefully another member will able to assist :)
 
Back
Top Bottom