post your Conroe temps!

[netby]

I Ferret

let the cpu reach 85ºC and then see what happens
( I´m almost 100% sure it went in a "throttling" state)

 

[Kaiju]

Do you know why this is? Perhaps Coretemp is wrong?

Take it to the E4300 overclocking thread mate in the CPU section as there are far more experienced people in there.

Offhand, you need to enable Intel Speedstep in your BIOS.

 

[WJA96]

Take it to the E4300 overclocking thread mate in the CPU section as there are far more experienced people in there.

Offhand, you need to enable Intel Speedstep in your BIOS.

Right idea, but it's TM1/TM2 you need to enable in the BIOS.

 

[ferret face]

ok cheers

 

[realscot]

E6400 @ 3.2GHz
1.22Vcore
Scythe Ninja
Idle 39c
Load 55c (orthos)
BF2142 after 2hours TAT reported 47c as highest temp in log.

New case arrived though so will see if it helps temps any.

 

[modo77]

On Arctic Freezer Pro 7. Does hit 75 on a few of the Orthos tests, but avg is 69. Idle 49c

The airflow in my Wavemaster case is very poor unfortunatly. Temps drop by about 20c when its open. Going to have to get watercooling soon.

FSB 1475
Multi 9x
Vcore 1.35
CPU VTT 1.45
1.2v HT 1.25

902 BIOS

 

[lunarwolf]

E6600 @ 3Ghz (9x333.3FSB | stock volt)

Orthos 3 hours no errors

Core 1 idle temp: 41C
Core 2 idle temp: 42C

Core 1 load temp: 52C
Core 2 load temp: 53C

 

[Thebug]

E6400 @ 3.208 GHz
1.392 VCORE
ASUS SILENT SQUARE
ARCTIC SILVER 5
IDLE 29c
LOADED 44c "ORTHOS"
USING INTEL TAT
NOT LAPPED

 

[msmalls74]

Does anyone else find that there cpu runs hotter under vista? Mine goes up a couple of degrees and the temps seem a bit more uneven. Does not seem to happen on full load though.

 

[WJA96]

Tcase/Tjunction

--70--/--85--85-- Shutdown
--65--/--80--80-- Throttle
--60--/--75--75-- Hot
--55--/--70--70-- Warm
--50--/--65--65-- N
--45--/--60--60-- O
--40--/--55--55-- R
--35--/--50--50-- M
--30--/--45--45-- A
--25--/--40--40-- L

That's excellent - they should put that in a sticky, it would prevent all those 'is my temp too high' threads. It's exceptionally easy to read too.

Very good in my opinion. Thanks.

 

[Jaaay]

E6400 - 426 x 8 = 3.41GHz @ 1.3250V
Cooler - Scythe Ninja Plus Rev. B

Stress: Core 0 = 63
Stress: Core 1 = 63

Idle: Core 0 = 35
Idle: Core 1 = 33

 

[Bomag]

Just went from

E6600 391*9 3.519Ghz at 1.5v
Ninja Rec B

Core 0 65c
Core 0 64c

to

Qx6700 320*11 3.520Ghz at 1.4v
TR Ultra 120

Core 0 58c
Core 1 54c
Core 2 52c
Core 3 52c

3.6Ghz is next up

 

[wizardmaxx]

Reviving an old thread, but was looking for a comparison temp for my E6400 on custom water cooling.

Temps seem ok, but since this thread is soooo old, what temps are you guys getting on the new D-Tek and swiftech blocks.