Re-housing a freebie system into a smaller case

KnightInd2000

KnightInd2000

KnightInd2000

Associate
Joined
24 Mar 2014
Posts
40
Location
Leicester
Re-housing a freebie system into a smaller case (Newbie)

Hi All, just joined and this is my first post.

A friend of mine has kindly given me his old system and although it is quite a bit quicker than my old system, it is too big and too noisy to put in the lounge - where my current PC lives.

So my plan is to re-house it into a smaller case whilst retaining as much of the donated system as possible. This includes water-cooling and my current case is just too small to house it so I’ve bought a new Fractal Design Define R4 for this purpose (I hope it’s suitable).

Now this won’t be an all singing, all dancing ‘benchmark smasher’ as I’m on a very tight budget and the parts are already 3 years old. But I’m posting because I’m completely new to water-cooling so will, no doubt, need a lot of help! Also, I’m sure I won’t be the last to take their first steps into the realms of a water-cooled PC so hopefully my learnings will prove of help to others.

I am prepared to do my research but if I asked a stupid question, please be forgiving!

First off here’s the donated system. Who recognises what?

fEqhgnn.jpg

LdjkiQw.jpg
 
Last edited:
My first task was to work out how to take the thing apart!
I stood the whole case in the bath and started with the pump. Once this was unscrewed from the base I could move most of it outside and set to work on the connector.
Now I know it sounds daft but I didn’t know how these worked so by trial and error I found that they have an outer compression ring (on the left) which unscrews and then slides down the tube which then allows you to simply pull the tube off barb part (on the right) and let the water drain away. Then the barb part unscrews from the pump top using a penny.

YGQt16J.jpg

Not sure what connector this is though
 
KnightInd2000 said:
My first task was to work out how to take the thing apart!
I stood the whole case in the bath and started with the pump. Once this was unscrewed from the base I could move most of it outside and set to work on the connector.
Now I know it sounds daft but I didn’t know how these worked so by trial and error I found that they have an outer compression ring (on the left) which unscrews and then slides down the tube which then allows you to simply pull the tube off barb part (on the right) and let the water drain away. Then the barb part unscrews from the pump top using a penny.



Not sure what connector this is though
Click to expand...

Looks like a monsoon compression fitting to my untrained eye.
 
KnightInd2000 said:
A friend of mine has kindly given me his old system and although it is quite a bit quicker than my old system, it is too big and too noisy to put in the lounge - where my current PC lives.

So my plan is to re-house it into a smaller case whilst retaining as much of the donated system as possible. This includes water-cooling and my current case is just too small to house it so I’ve bought a new Fractal Design Define R4 for this purpose (I hope it’s suitable).
Click to expand...

noooo dont do it!
the current rig has a 360 and 240mm rad, the define r4 wont be able to fit it.
just turn the fan speed down on the current rig and it'll run quiet. 600mm of rad is more than sufficient to cool the beast, even at lowest fan settings.
 
also wanting to know what spec the system is as it looks to be a bit of a beast, especially if the person had to watercool it. Might of got an amazing system.

Im with the person a few posts up i dont think you should put it in a smaller case that TJ07 is a fantastic case just turn down the fan speed
 
tamzzy said:
noooo dont do it!
the current rig has a 360 and 240mm rad, the define r4 wont be able to fit it.
just turn the fan speed down on the current rig and it'll run quiet. 600mm of rad is more than sufficient to cool the beast, even at lowest fan settings.
Click to expand...


Unfortunately the TJ07 won't fit in my desk so the Define R4 had to be purchased.
Appreciate that this will be a bit of a squeeze and I’m not making my first steps into water-cooling very easy but needs must. And to just leave it alone would be a bit boring!
 
Last edited:
I won’t be able to fit the EK-BAY SPIN Reservoir into the Define R4 because I want to retain a DVD drive in one of the 2 bays and this is a dual bay res. So I’m thinking of attaching a reservoir to the pump. The pump is a Swiftech MCP655 which I think is the same as a Laing D5. Is this correct?

rtG0cKL.jpg

So does anyone know if I can remove the EK top from this pump and replace it with one of these?... http://www.overclockers.co.uk/showproduct.php?prodid=WC-319-EK
 
yup you certainly can. pop the 8 (or possibly 4) screws out of the back. and just pull it out of the block. take the little square bracket off too (that has to be pulled backwards over the wires)

then its just a case of fitting the one from OCUK :)
 
You must log in or register to reply here.
Back
Top Bottom