• Notice regarding image hosts and attachments. See here.

Road Cycling Essentials

Status
Not open for further replies.
That wilier is nice! We recently started doing them and I've got a soft spot for the izoart XP 105. Even the tristena 105 would do me.

Need to build the gran tourismo athena in the next few days.

Pro stuff is nice and what I tend to get in for people. Even the £30/40 lt/plt stuff is nice if you can't stretch to viben7s kit.
 
then its your deep drop brake calipers that are the problem and not the wheels, the shop has obvisouly set the pads to to the highest position the could.

Thanks, I had come to the same conclusion after a short discussion with someone else.

I'm not sure why the bike shop didn't raise the issue of the brake pads not having sufficient reach before, as they raised other issues that required replacing parts.

The front wheel they supplied needs to go back to be replaced anyway, as it has some existing damage. I'll see what they can do about the brake pad alignment issues too.

Just wanted to confirm that there is no tweaking I can do to resolve it.

Thanks all
 
me - Garry :)

haha, cant help reading that in a 'Gary tank commander' voice :p

is the other Gary back at work yet? Any good stories from the tour?
What happened to him in stage 3 for a DNF? Hopefully just a puncture or something?
Good result for Endura anyway :D
 
haha, cant help reading that in a 'Gary tank commander' voice :p

is the other Gary back at work yet? Any good stories from the tour?
What happened to him in stage 3 for a DNF? Hopefully just a puncture or something?
Good result for Endura anyway :D

haha seriously like?

he s not back yet mate, tue/wed are his days off so wont find out till thur.

Him and Davie Lines DNF from what i gather but i dont know why...

Jordan did pretty decent tho!
 
Just been to have a look at a relatively new local cycle shop, really shouldn't have gone.

Someone who i know from school works there as a mechanic and gave me the opportunity to have a few days test ride with some Dura-Ace C35's and a couple of hours out on a new Trek Ultegra Di2.

I've decided I must resist otherwise I'm just going to want to spend all my money :p
 
Sounded like a **** couple of days to be racing in from what I've heard/saw.

My boss is off for a few days as he collided with an NEG bike coming down the talla....his frame, shifters and bars are gubbed he was saying on the phone.

So he had an Felt F1 before, broke that when his R-Sys front wheel collapse.
Replaced it with an AR1 Garmin replica...broke that beyond repair.
Then was on the newest F1 and has wrecked that in now.

That in two years of racing :| maybe he'll just take his pick from an older AR4, an F2 Di2 or this Wilier Gran Turismo i've just put together.
 
Slightly technical question regarding fork stems and headsets.

A while ago I had a very nice steel frame that was damaged in a crash (top and down tube bent). I've just bought a replacement 531c frame without forks which is a better size for me, I had the genius idea that I could swap everything over from the old bike including the forks. The old bike used a threaded headset and had a head tube length of 22cm. The new frame has a head tube of 16cm. So I think I have 2 options but one might not be possible.

1. I can get 6cm lopped of the top of the stem and a new thread cut in (current thread only goes down 4.8cm) and reuse the old threaded headset. I don’t see any mechanical problem with this option but not sure of the cost yet.

2. Since there should be 6cm of excess tube (1.2cm unthreaded) I could get a threadless aheadset which would be more modern (there is also some wear to old one). I am not sure if the clamp which connects the fork stem and handlebars is safe to attach to a threaded section of tube. I’ll probably check what they think in a bike shop but it would be interesting to hear any thoughts on this.

Couple of pics:

DSC02639.jpg

DSC02640.jpg
 
1. I can get 6cm lopped of the top of the stem and a new thread cut in (current thread only goes down 4.8cm) and reuse the old threaded headset.
This would be the best option. Or it might be cheaper to find another fork the right length on ebay.


2. Since there should be 6cm of excess tube (1.2cm unthreaded) I could get a threadless aheadset which would be more modern (there is also some wear to old one). I am not sure if the clamp which connects the fork stem and handlebars is safe to attach to a threaded section of tube. I’ll probably check what they think in a bike shop but it would be interesting to hear any thoughts on this.

I dont see it being a massive problem to clamp a stem onto a threaded tube as long as the headset is on an unthreaded bit of the fork. The threads will probably wreck the inside of the stem clamp so once you put it on, it's best that you dont use it for anything else.

Make sure you get things the right size tho. Your threaded fork tube is probably 1inch diameter where most threadless setups use forks with a 1 1/8 inch diameter tube. You can get threadless stems, headsets, etc in 1inch diameter but they are sometimes hard to find.
 
Last edited:
Thanks, you are right about the size. I was looking at this threadless headset, the 1" threaded seem to be getting rarer and more expensive these days. I'll probably decide when I find out the price of altering the fork. If I set it up right the first time I shouldn't need to alter the bar height again.
 
Thanks, you are right about the size. I was looking at this threadless headset, the 1" threaded seem to be getting rarer and more expensive these days. I'll probably decide when I find out the price of altering the fork. If I set it up right the first time I shouldn't need to alter the bar height again.
Not really, you can get 1" threaded stuff in a lot of places and it's usually cheaper than threadless. I think my last one was £15 for an all-alloy Tange one with sealed bearings and you should be able to get a chromed steel one for under £10. Unless you can't get the top of that fork threaded I can't think of a good reason to go to threadless on an older frame and fork, unless you specifically want to use the new style clamp stems instead of a quill stem and with a quill you get much more adjustability up and down.

Try Cycle Basket for 1" threaded: http://www.cyclebasket.com/m9b0s400p0/Components_/Headsets_-_Threaded_Headsets_1_inch_

Quite a few on eBay for buttons too.

Cycle Basket also do 1" threadless: http://www.cyclebasket.com/m9b0s398p0/Components_/Headsets_-_Aheadsets_1_inch_
 
It's time to really hit the diet hard so that I can have a new bike for my week off.

I currently weigh 16st 10 and I'm not going to order myself a new bike until I hit 15st something, it gives me about 3 weeks to knock off 10lb+. I know it's doable as long as I'm careful with my diet and put in a few extra miles each evening. I'm down from 22st 10 so cycling has really turned my life around!
 
Wow Rusty, that's some achievement already! Well done.

In other news, my left Shimano SPD pedal will not come off. Been on there two years through all weather. I want to fit my Look Keos :( I'm turning the wrench towards the rear but it's just not budging. At one point it felt like I was going to snap the frame I was putting that much force on. Hopefully after soaking overnight it will have a chance of moving later. I felt like throwing my bike against the wall!
 
Wow Rusty, that's some achievement already! Well done.

In other news, my left Shimano SPD pedal will not come off. Been on there two years through all weather. I want to fit my Look Keos :( I'm turning the wrench towards the rear but it's just not budging. At one point it felt like I was going to snap the frame I was putting that much force on. Hopefully after soaking overnight it will have a chance of moving later. I felt like throwing my bike against the wall!

Please don't take my head off, but you are trying to unscrew it the right way aren't you? :)
 
As above, remember the left pedal has an opposite thread so that it doesn't unscrew as you pedal.

I feel you may be a bit embarrassed later :p

If not then all I can recommend is a temperature change to make the internal screw expand/contract and loosen any debris, so get a hair dryer on it for a bit and then in a bucket of ice cold water with your bike on its side if you can.
 
I feel you may be a bit embarrassed later :p

He might well be.
But it's also possible that he's doing everything right and just cant get it off. I'v been there myself. Ended up wrecking my pedal spanner before i finally got it off using a normal spanner with all my weight on it.
 
I just sold an Ultegra 6600 groupset and had to include one spd pedal in the deal as I just couldn't get it off. I amount of soaking helped, I just didn't have the leverage.

Should imagine the chap in the shop managed it in 2s once he'd extended his pedal spanner with a 6' length of scaffold and pressed lightly with one finger.
 
Status
Not open for further replies.
Back
Top Bottom