• Notice regarding image hosts and attachments. See here.

Road Cycling Essentials

Status
Not open for further replies.
Gutted mate.Hope they sort it out for you quickly and as pain free as possible.

They could argue you fannied about with it to be stubborn but they would have to be really awkward.

Torque wrenches aren'y everything...I've seen stem bolts break getting torqued to spec. I do mine by hand to be frank but on other bikes I'll use a torque wrench.

I forgot to thank you for your (and everyone else's) advice on my BB creak I had the other month, it was just lacking grease and all has been well since.

Now, after an enthusiastic cycle home last night there is a bearing in my rear wheel that sounds like it's been replaced with gravel. Only happens when free wheeling so I'm assuming there's a bearing in the cassette (shimano 105) that's knackered?
 
Really wishing i didn't have to deal with Halfords when buying a Boardman now. The first guy i spoke to didn't even understand how a theadless headset worked, he was stood there wobbling the fork around without the stem attached, claiming that the bung in the steerer should stop it from wobbling.
 
I forgot to thank you for your (and everyone else's) advice on my BB creak I had the other month, it was just lacking grease and all has been well since.

Now, after an enthusiastic cycle home last night there is a bearing in my rear wheel that sounds like it's been replaced with gravel. Only happens when free wheeling so I'm assuming there's a bearing in the cassette (shimano 105) that's knackered?

Shimano use loose ball bearings on each side of the wheel. Once they sound like that you'll find the driveside will have no grease and rusty bearings. You would hear that crunch as you pedal though. Hopefully it would just be a dry freehub body. That only spins when you stop pedalling. usually its because degreaser has been sprayed straight onto the cassette...that then dries out the freehub body.

The freehub body can be anything from £25-40. I'll check to be sure. Then maybe £10-15 to take the hub apart and put new bearings in.#

Edit: Freehub body is in stock and is £34.99.

FH-5600 complete Freehub body
Code: 3CJ 9807

This is assuming it's a 105 hub and not just the cassette. Part number will be written on the hub itself.

http://techdocs.shimano.com/media/t...FH/EV-FH-5600-2458C_v1_m56577569830728267.pdf




Really wishing i didn't have to deal with Halfords when buying a Boardman now. The first guy i spoke to didn't even understand how a theadless headset worked, he was stood there wobbling the fork around without the stem attached, claiming that the bung in the steerer should stop it from wobbling.

good luck :)
 
Last edited:
I've always sprayed degreaser directly onto my sprockets :eek:

Is it best to just dip a brush into the degreaser and scrub?

I usually just get a rag and wipe as much as possible off that way.

Then, with the wheel off, sit pulling a rag through the gaps in the sprockets working my way round. That usually get's most of the crap off. Either that or I take if off and blitz it with the finish line degreaser in the sink, getting high off my head in the process.

Degreaser working it's way into the hub/freehub body kills them. Same with pressure washing that area of the bike.

"But I wash my bike all the time!!"
"Pressure washer?"
"Ahuh"
"Well then....."
 
Funny I washed my bike on Sunday but I use a bucket of water and brushes. I used Muc Off bike spray (think it's PTFE?) around the rear mech and cassette, is this likely to have killed it? Thought it was more of a lube :p

It's a Felt hub with 105 cassette so not sure what that means in terms of free hub body. I'll just drop it into the back shop when I'm back from my holiday. Cheers for the help.
 
Funny I washed my bike on Sunday but I use a bucket of water and brushes. I used Muc Off bike spray (think it's PTFE?) around the rear mech and cassette, is this likely to have killed it? Thought it was more of a lube :p

It's a Felt hub with 105 cassette so not sure what that means in terms of free hub body. I'll just drop it into the back shop when I'm back from my holiday. Cheers for the help.

Ahh I see! I think felt hubs are just based the same as formula freehub bodies. Ignore my last post on that part.

Doubt it would have killed it but cheaper hubs can run dry shockingly quick.

Could be around £40 to get a freehub changed and a newR500 rear wheel isn't that much more.

The freehub body of my R500 rear wheel sounds dry as #### as it was left in a poor state for over a month. Cheap parts FML...
 
Last edited:
Crappy commute this morning, had a nasty near miss emergency stop with a bunch of pedestrians crossing against the light ignoring me heading towards them. Then 5 minutes later the same thing again but couldn't avoid a girl who just stepped out without looking. Thankfully she didn't hit the ground too hard and just suffered a small cut by her eye.
 
Serves her right. Did you come out of it ok?

My friend is still suffering with his elbow 3 months after he hit someone who stepped out at a crossing without looking. Really he should have got his details and be charging the idiot for physio sessions.

Speaking of which, I cancelled my bike insurance with E&L last week. Who is everyone here with?
 
Isnt that illegal over there? (or do people just ignore that law?)
In theory yes. But there's no way I'd win any legal fight. I was just grateful that she wasn't hurt badly.

I came out of it fine, didn't go down. Although my laptop is refusing to work on my docking station at work now.
 
Last edited:
Got home early from work, and then spent about 30 mins picking out flint and other small bits of debris from my tyre thanks to the council stripping a road down to the foundation layer.

I think I'll avoid that strip of road by cycling on the pavement until they layer it with tarmac again.
 
Just to let you guys know, We at Pedal Power in West Calder are now doing KTM bikes as of next week.

I predict them to be the next Cube in terms of bright colours, nice finish and amazing spec for the money.

Not sure how many dealers the distrobuter has in the UK as of yet but google throws up no results so i think were the only dealer in Scotland so far.

Im picking up either a Strada 3000 or 4000 for myself in the next week or so,

This is their website so if any of you are looking for a new "summer bike" shortly once the weather picks up, you can give us a bell in the shop and hopefully i can sort out a little discount for OCUK members :)

http://www.ktm-bikes.at/
 
Do you have a price list? (or at least a rough idea of prices)

edit: also, the spec list on the ktm website is terrible, i have to hover over like 50% of the icons to figure out what they mean :(
 
Last edited:
Theft doesn't concern me, it's getting sued and not having any liability insurance even when it's not my fault.

i joined britishcycling.org.uk and for around 22 quid a year get liability insurnace cover included as well as all the other perks

well worth it for piece of mind, and much less than upgrading a component on your bike....
 
i joined britishcycling.org.uk and for around 22 quid a year get liability insurnace cover included as well as all the other perks

well worth it for piece of mind, and much less than upgrading a component on your bike....

I guess you didnt look at his location? :p
 
Status
Not open for further replies.
Back
Top Bottom