• Notice regarding image hosts and attachments. See here.

Software to test temps, load etc?

The 4ghz Rampage?

Both systems will be good, i think it just depends on personal preference on gigabyte or asus...
 
Hi folks,

Decided to update this thread rather than my epic original build thread, as it's more closely related to the problems I had.

So, new bundle arrived and appears to be a totally new set of components - definitely a new mobo, probably a new CPU (not sure, as OCUK took and kept the Retail box) and possibly new RAM, but this time they included a set of the funky blue heat dissipator thingies on the Viper sticks - very cool!

I'm now running Prime95 on blend mode and it's idling at around 42C and maxing out at 83C - MUCH better temps (previous build temps were hitting low 90s) and exactly what the OCUK staff said it should max out at (they said anything up to about 84C is ok).

Looking good so far - will let Prime run for an hour or so and run some other test apps like IntelBurnTest and BurnInTest just to make sure.

Looking very promising so far! Certainly no hiccups with the build, everything went smoothly again.

I'll post back with some more results.

Cheers!
 
Oh and by the way, the explanation OCUK gave for the temps issue on the previous bundle was that the battery on the mobo was faulty and the BIOS wasn't retaining the settings. They are not entirely sure this is the problem but basically gave me a totally new bundle as a result.
 
passed 8k test after about 35 mins, maxed out at 85C but I was e-mailing and browsing at the same time, so pushing it beyond normal "load" use. very pleased so far - all seems to be working!

now running IntelBurnTest.
 
seems to be idling at around 54C now, with the case on and fans on medium. seems ok, maybe a touch hotter than I'd hoped, but I'm really not bothered, as it never gets over 85C under full load and seems rock stable so far. hopefully with a little more burn time the thermal paste will work better and things will drop a few degrees.

thanks for everyone's help through this! much appreciated.
 
I've noticed that it's hitting up to 89C when rendering now that the sides of the case are on. Is that safe? Better to remove the sides? Or is something not right.

Any ideas?

edit: make that 90C!
 
Last edited:
I've had a few thoughts on this overnight and I'm going to do some tests shortly:

1) CPU fans may not be spinning at exactly the same speed in push/pull config, causing one fan to overpower the other and increasing temps. i need to check that plugging them into PWR_FAN and SYS_FAN(1, 2 or 3) is OK. Will try in different headers and will monitor fan speeds using SpeedFan.

2) My biggest hunch: the HS surface is not flat. Will remove HS from CPU and see if "butterfly" effect is present in the paste. If the entire surface of both HS and CPU isn't covered in paste then this is the problem. (Poor HS)

3) The entire HS can be rotated 180degrees. I may try this.

4) Double check that HS risers are correctly screwed in and not too high/low

5) Try plugging PSU into wall, not expansion sockets

6) Had feeling I may have used 2 year old Arctic Silver 5 instead of the newly supplied AS5 from bundle. Will try reapplying with new AS5.

7) If New AS5 has no improvement, will try with Noctua's own paste.
 
can anyone have a quick look at the list above and tell me if anything is wrong/unnecessary/right to check?

i've got OCUK on to this but any help from you guys would be extremely appreciated!

cheers
 
Well this has all finally been sorted out. Noctua replaced with Megahalems and temps are down by 10C! Max load down from 91C to 81C, idle down from 45C to 39C. A massive improvement!

I've sent the Noctua back to OCUK but my guess it was just faulty somehow, a bowed HS surface or something.

Cheers!
 
Hi guys,

Unfortunately I'm back again with troubles...

Idle temp with case sides on is now 52C, not 39C and max load temps are hitting the high 80s. Not so much a problem in itself, it's more the system stability that's the problem. I'm getting random crashes after running long 3D renders for a few hours. I have no idea why this is happening. I presume something to do with unstable O/C? I've already increased vCore up to 1.3 instead of OCUK's default of 1.275. Should I go higher? Maybe 1.35?

Any advice would be very much appreciated, as this system is currently unusable for my work...

Cheers!
 
Back
Top Bottom