Loop

[extrememachine]

Have finalised my watercooling parts, just need an idea how the loop is supposed to go.

1 cpu block
3 gpu blocks
1 pump
1 radiator
1 reservoir

 

[extrememachine]

Had a feeling I may have needed a +1 fan rad, is it really imperative or can i do without?
My current rad is a 3fan
cosmos 2 ultra case)

 

[extrememachine]

4960x 3 titan black SC both with w.blocks

 

[extrememachine]

I will fit a +1 fan rad in there so effectively 4 fans, I doubt that many would cause an issue.

 

[extrememachine]

Had an external rad in the past, definetely not going down that route again.
I will see how it goes anyway.thnx for your advice..

 

[extrememachine]

No problem at all when you heat damage all your kit with in adequate heat dissipation be sure to let us no , i remebered you should be able to get a set up like this into your case its not ideal but better than what you would suggest

http://www.overclockers.co.uk/showproduct.php?prodid=FS-368-OE its essentially two 360 rads

With a 360 on top a 120 slightly below.Maybe I can fit a 240 at the bottom by the power supply, but is this all really necessary??

 

[extrememachine]

Ok will get a 2 fan rad for the base of the case like this dude

:
120mm or 140mm?

 

[extrememachine]

A 360 a 120 and a 280 should do the job cosmos 2 case or not.

 

[extrememachine]

you would probably get away with that yes. with correct type high sp fans.

Some assurance, hallefrikinlua"!

 

[extrememachine]

just please dear god if you are going to try this get an inline water temp sensor so you can tell before your water temp gets into the danger zone and shut the pc down

Will boot the pc up quickly and initiate speedfan or evga precision.
Received the 280mm radiator just managed to fit it in underneath as for the single rad, looks like it wont fit in this case.
So got a 360 and a 280, hoping it does the job.

 

[extrememachine]

Yh will post some tomorrow bit tired atm.
Just a quick query, how much of a gap does a radiator need.
E.g. 2 inches away from the chassis wall.?

 

[extrememachine]

Ok so i finally got my 2 slot tubes ek 10/12mm, so have all the parts I need.
But am not really sure how to do the loop.
components:

1 pump
1 reservoir
3 gpu block
1 cpu block
2 rads

Any tuts?

 

[extrememachine]

Situation still ambiguous for me, any pictures, video guides?

 

[extrememachine]

Put all of the stuff in the case then just plumb up in the simplest way possible. You don't need any special order.

Lol.Its that simple?

 

[extrememachine]

Saw a diagram and seem to get it, However I am still unsure about the the setup for the Graphic cards (parallel orientation) as well as the fact there's another rad.
Any pics that display this?

 

[extrememachine]

http://www.overclockers.co.uk/showproduct.php?prodid=WC-102-AQ&groupid=962&catid=2141&subcat=2142

this pump

 

[extrememachine]

What if I replaced the cosmos with a tj11 silverstone temjin, I see lots of potential in terms of room.
How do people place a 4 fan rad at the base when there is need for a PSU?
Could I fit 2x 4fan radiators?

 

[extrememachine]

Enthoo primo looks good but the tj11 is still my no1 choice so far

 

[extrememachine]

Damn right
In all seriousness, if there are any XL-ATX cases coming in the near future I can wait

 

[extrememachine]

MAGNUM TH10A

This one's not bad