Official DFI NF4Ultra-D/SLi owners thread.
- Thread starter ricco
- Start date
Soldato
Down1oader said:mines comin monday, dammnit i knew i should have cancelled my order
err - why?!
Soldato
pacegod said:
I take it you're using dual GTs?
If you switch to the 71.21 drivers you'll go over 10k in 05 and 22k in 03 easily.
What clocks are you running your GTs at? Mine will only go up to 385/1100 without artifacts
It's a pity, as one card is rine up to 440/1180, whereas the other doesn't like anything above 385/1100. With SLI you have to run at the pace of the slowest of course...
Permabanned
cause i wanted the dr duff but didnt want to go to the back of the qeue 
i plan on getting mannnny hard drives 
i plan on getting mannnny hard drives 
Associate
Can't wait for mine on Tuesday.... This board better be worth the pain i've had getting it...
Associate
They are running at ultra speeds 400-1100. On my Asus they would run 420-1120 easily. Am going to overlock them and cpu this afternoon. Running 66.93 drivers at the moment, dont normally like running betas. Might give them a go though.
Will I have any problems with this board and Geil Value RAM? Can't afford faster memory at the moment.
Damn, there doesn't seem to be any low profile chipset heatsinks out there
Edit: Will this be up to the job or do you think an active cooling solution is a must for this board?
Vantec Iceberq CCB-A1C VGA & Chipset cooling kit (SY-000-VT)
Damn, there doesn't seem to be any low profile chipset heatsinks out there
Edit: Will this be up to the job or do you think an active cooling solution is a must for this board?
Vantec Iceberq CCB-A1C VGA & Chipset cooling kit (SY-000-VT)
Last edited:
Associate
Cheers ricco for answering my question above. Maxtor DM+ 10 here we come...
Associate
Here's my first real attempt at o/c the Ultra-D
Sorry about the size
This is with a watercooled FX55
Anyway, for some reason the OCZ PC3200 Rev2 seems to need a LOT of volts on this board. Won't even post properly > 270 HTT with less than 2.9 volts. Rather different to my Neo2 which would do it at 2.7 volts. But looking at XS and DFI forums other people have found the same. Hopefully a new BIOS soon (this is with beta 2.01)
Sorry about the size
This is with a watercooled FX55
Anyway, for some reason the OCZ PC3200 Rev2 seems to need a LOT of volts on this board. Won't even post properly > 270 HTT with less than 2.9 volts. Rather different to my Neo2 which would do it at 2.7 volts. But looking at XS and DFI forums other people have found the same. Hopefully a new BIOS soon (this is with beta 2.01)
Associate
macachia said:surge, what watercooling system is that?
Hi
Its:
2 x Eheim 1048s in series
Black Ice Pro 2 with 1" shroud and 2 x Panaflo L1As at 9-12 volts
Swiftech 6000
Maze 4 GPU
About to mill a high-flo block for the NF4 chipset
Should say that the screnshot was obviously taken when the CPU was no longer at max load. CPU temp during SuperPi was 40 deg C
Cheers
Nice 1 surge,
hhas anyone noticed slightly faster boot times with this (or any Nf4) compared to their NF3 ?
The more I crank up the HTT the quicker I seem to load windows, even if the CPU/mem are relativeley the same frequency.
Also , I did'nt realise, but I have been running 400HTT with a 4x HTT multiplier too.
hhas anyone noticed slightly faster boot times with this (or any Nf4) compared to their NF3 ?
The more I crank up the HTT the quicker I seem to load windows, even if the CPU/mem are relativeley the same frequency.
Also , I did'nt realise, but I have been running 400HTT with a 4x HTT multiplier too.
Soldato
- Joined
- 10 Apr 2004
- Posts
- 13,489
It has arrived Gonne be putting together after school!
Gonne be putting together after school!
Soldato
Concorde Rules said:It has arrived
HTH did you afford all that lot when you're still at school?!
Hardcore paper round?!
Associate
Whats with all the power connectors on the board? I can understand the 24pin and 4pin connectors but whats with the 4pin molex and floppy type connector on the board too?