PHANTEKS EVOLV X & P600S

clone · 25 Sep 2018 at 14:58

Both my doors look ok as far as I can see.

Phanteks_Care · 25 Sep 2018 at 15:32

orbitalwalsh said:
@Phanteks_Care whats your email for Zeeflyboy?

also been trying to contact Phanteks on separate manor and haven' have a reply back .

you can contact me @ rma[at]phanteks.com

orbitalwalsh · 25 Sep 2018 at 15:41

Phanteks_Care said:
you can contact me @ rma[at]phanteks.com

thanks

Zeeflyboy · 25 Sep 2018 at 16:42

True, since phanteks are offering I suppose I should take them up on it...

Thought this might be of use to those looking at radiator options, top is an EK Coolstream SE 280mm and the front is an EKCoolstream CE 420mm. Fit very well but that front slot is definitely tight for 140mm base rads.

Also thought some might like to see the PCI-E extension fitted:

Distracted · 25 Sep 2018 at 17:05

I like that the pcie ribbon/cable is narrower than the alternatives like those from Lian Li.

It's a small thing, but makes the cable less in your face.

clone · 25 Sep 2018 at 17:45

As the lower left door secure screw thread was stripped I tapped it out from 6/32 to m4,had these thumbscrews left over from my corsair 570x build I thought I would use them.

clone · 26 Sep 2018 at 15:03

Got my flexible internal USB 3.0 cable today this should help with the gap in the case motherboard cover.

Mcthommo · 26 Sep 2018 at 16:33

Would love to see the room in the foot of the case after front 360 rad to see if the 3.5 drive cage is possible as still tempted by this case

Mcthommo · 26 Sep 2018 at 16:34

Would love to see the room in the foot of the case after front 360 rad to see if the 3.5 drive cage is possible as still tempted by this case

clone · 26 Sep 2018 at 16:53

So good you had to say it twice

Mcthommo · 26 Sep 2018 at 17:15

clone said:
So good you had to say it twice

It was fat fingers on stupid phone

Rensin · 26 Sep 2018 at 19:01

Just started adding white vinyl but unsure if prefer the Gunmetal?

Mcthommo · 26 Sep 2018 at 19:06

nice contrast

Mcthommo · 26 Sep 2018 at 19:26

Also, has the fan hub been sorted out by which I mean have you got the correct connection method- I currently run everything through my Aquaero 6 and cant see anywhere for me to install it in this case without a major hack job

clone · 26 Sep 2018 at 21:45

Gave the phantek tech guy a load of Imformation over several emails and just waiting on him getting back to me again with their results.

Zeeflyboy · 27 Sep 2018 at 08:34

Rensin said:
Just started adding white vinyl but unsure if prefer the Gunmetal?

Looks very striking, but then I do love the gun metal too.

I guess it depends how it fits into your decor and what you are planning build wise inside.

clone · 27 Sep 2018 at 09:48

Got a email yesterday about my replacement top grill,it's been sent out got to say the phantek support is spot on.

clone · 27 Sep 2018 at 11:08

Not to good picture of my black case.on air till i save up for the last of my watercooling.

Fexable 3.0 header cable now the motherboard cable cover is far better now.

LackyT · 27 Sep 2018 at 12:50

Mcthommo said:
Also, has the fan hub been sorted out by which I mean have you got the correct connection method- I currently run everything through my Aquaero 6 and cant see anywhere for me to install it in this case without a major hack job

Fan hub working fine here:
- Connect your fans up to the hub, making sure you populate the white connector first / as a priority.
- Connect the hub fan lead to the M/B fan header. I used the CPU header as recommended, but it should also work on a normal chassis header as long as you can change it to PWM mode in the BIOS
- Connect the hub SATA power cable
- Profit

clone · 27 Sep 2018 at 13:19

What the serial number on your fan hub,it's on the left side.