• Notice regarding image hosts and attachments. See here.

Road Cycling Essentials

Status
Not open for further replies.
Something I should ask while I'm talking to people who know their stuff, is why does my back wheel slide (from left to right) when I use my back brake? Most of the time I use my front brake on it's own, but there's the odd time I use both the front and back (for example when going down a steep hill) and I almost always end up going all over the place and coming off (I came off once, the first day I got it; straight into a lamp post, dented the frame and injured my hand).
 
Something I should ask while I'm talking to people who know their stuff, is why does my back wheel slide (from left to right) when I use my back brake? Most of the time I use my front brake on it's own, but there's the odd time I use both the front and back (for example when going down a steep hill) and I almost always end up going all over the place and coming off (I came off once, the first day I got it; straight into a lamp post, dented the frame and injured my hand).

You are locking up the back brake and skidding. You need to press less firmly on the lever and I might suggest also moving your weight towards the back when you brake; when slowing the bike will rotate around the front axel tryinging to rip you over the bars. Even at low speed this lifts the rear wheel and makes braking less effective.
 
Something I should ask while I'm talking to people who know their stuff, is why does my back wheel slide (from left to right) when I use my back brake? Most of the time I use my front brake on it's own, but there's the odd time I use both the front and back (for example when going down a steep hill) and I almost always end up going all over the place and coming off (I came off once, the first day I got it; straight into a lamp post, dented the frame and injured my hand).

I believe it is because your weight isn't far enough back when you brake. I've experienced similar before and that was the cause.
 
It depends on the geometry of the bike too. My fixed-gear is incredibly low at the front and short wheelbase, so you'll always find yourself locking the back wheel up. Just let off the brake a bit and get back on it; it just takes a bit of practice. As with motorbikes, it's terribly poor practice to only use the front brake. The rear brake is excellent for making minor positional corrections when cornering and shaving off speed without mashing the front brake, particularly in the wet, so try to get used to using it :)
 
wheels in for a true, had a worrying thought on the way in, how do I know if they are steel or alu (without a magnet to hand)?!?!
but the guy seems happy to fix em so I'll wait for the results in an hour or three!

may have to invest in some training soon!

I was reading on doc browns website that factory chain lube is baked on (and advise on how to do it) anyone know where you can pick some up?
 
Last edited:
wheels in for a true, had a worrying thought on the way in, how do I know if they are steel or alu (without a magnet to hand)?!?!
but the guy seems happy to fix em so I'll wait for the results in an hour or three!

easy

steel rims cause you to crash to a horrible death at the first hint of rain. and weigh NINE MILLION TONS.
 
thats ok then these only weigh 1.56 Tonnes.
not sure if it would be such a bad thing if I _HAD_ to buy new wheels ;)
 
playing the ebay waiting game for a boardman road to get a geared bike in the garage so i can do some longer rides

if anyone spots one anywhere let me knoww.. small or XS should be ok
 
guys whats the best way to clean a chain? at the minute i just WD40 it up, put loads on a rag then run it thought it until its pretty much spotless, then i re lube it
 
Bought this bike off of a friend's Dad not too long ago. Ride fairly well, though the wheels are not amazing. Considering getting new tyres for it as I can't really afford wheels, I love the colour of the frame, it was built up from nothing in the 90s I think, and the wheels in the photo are the same ones that came with it. Wouldn't mind getting a more modern bike eventually but for the amount of commuting I do at the moment, I don't see point in spending money I don't have.

http://i520.photobucket.com/albums/w321/M12Secrets/SAM_0260.jpg[IMG]

Cost me £100.

//hadn't see the "Show your bike off" thread, shall post it over there now.[/QUOTE]
Is that Reynolds 531 stickers? If so, that's not a bad bike and good for the money you paid. If it's the right size for you and comfy, I'd hold on to it, even if you decide to repaint it later. 531 makes good frames :)

[quote="Hamster, post: 22189100"]People scoff but it works for him and I can't see the problem with that.[/QUOTE]
Don't you dare ever say if a saddle is not 100% spirit-level perfect it'll be useable. Don't you know if it's even slightly out it'll kill you? :p

[quote="Kimi, post: 22193432"]guys whats the best way to clean a chain? at the minute i just WD40 it up, put loads on a rag then run it thought it until its pretty much spotless, then i re lube it[/QUOTE]
OMG you don't use WD40 do you? What about teh silicones? but it's not a lubricants and it'll cause your chain to snap and all the nuns will die.

I'm having one of those days :p

Yeah sounds good, that's the way I do it. No need to get it spotless, but do use lube afterwards because WD40 is very light and will evaporate off.
 
Don't you dare ever say if a saddle is not 100% spirit-level perfect it'll be useable. Don't you know if it's even slightly out it'll kill you?

Having your saddle at some silly angle because "its the only way to be comfortable" is usually just compensating for having the wrong components on your bike or having them setup incorrecly.

OMG you don't use WD40 do you? What about teh silicones? but it's not a lubricants and it'll cause your chain to snap and all the nuns will die.

Ever tried removing the dirty lube from your chainstays with WD40? Hmmmm, it breaks down the greasy marks quite well. Surely it wont do the same to the lube inside the chain rollers tho......will it?
 
Last edited:
Having your saddle at some silly angle because "its the only way to be comfortable" is usually just compensating for having the wrong components on your bike or having them setup incorrecly.

The chap I'm talking about does it on all of his bikes and he has and has had a fair few over the years, even custom built frames! Can't say that it works for me though; I've tried angling the saddle down and I just slip off!
 
guys whats the best way to clean a chain? at the minute i just WD40 it up, put loads on a rag then run it thought it until its pretty much spotless, then i re lube it

there's a Sheldon brown article that says about cooking your chain in some citrus degreaser before re-lubing it up.
tempted to do that next time!
 
guys whats the best way to clean a chain? at the minute i just WD40 it up, put loads on a rag then run it thought it until its pretty much spotless, then i re lube it

When my chain needs a good clean, I take it off from the powerlink, put some Finish line degreaser in a small takeaway tray and snake the chain so that it's flat and all sitting in the liquid then turn the chain onto it's other side. Then using an old toothbrush clean any caked on dirt which usually comes of quite easily. Then I'll hose the chain down, put it in a bowl of hot soapy water, shake it about, use a different brush to clean it again and hose it off to finish before spraying on a bit of water displacer and letting it dry on the back of a garden chair. Comes out sparkling every time. Then lube it properly once back on the bike of course.
 
Is that Reynolds 531 stickers? If so, that's not a bad bike and good for the money you paid. If it's the right size for you and comfy, I'd hold on to it, even if you decide to repaint it later. 531 makes good frames :)

It certainly is!
SAM_0606.jpg

SAM_0608.jpg


Shame I went and dented it. Any advice on adjusting seats or setting up the bike in general? I don't know if it would be worth changing parts or not, I don't know much about bikes as it stands. But yes, the frame seems right size for me. :D
 
building up my new wheelset this evening.

If you've never built a wheel before, get Roger Musson's book from wheelpro.co.uk and give it a go. You're not a complete bicycle mechanic until you do!
 
building up my new wheelset this evening.

If you've never built a wheel before, get Roger Musson's book from wheelpro.co.uk and give it a go. You're not a complete bicycle mechanic until you do!

Excellent resource. I've been wanting to make the truing stand that he's created a design for in that book. Will have to get round to it sometime soon!
 
Status
Not open for further replies.
Back
Top Bottom